Having problems with your Flat Panel Televisions ?

No Vs Voltage (200-210) out of a BN44-175A Samsung Power supply


\015 Checked voltages on power supply and no Vs voltage apparent. The Va Voltage (55-65) is good but no high voltage coming out of board. Voltage apparent at Transistor QS801 but no voltage out of coil or to the two capacitors before leaving the board. TV symptom is where TV turns on and off in a cycle. No Picture but slight snow/noise on screen.\015

Answers :

If no voltage out either a short on the line pulling it down or its at the source--usually one or the other.

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

No Vs Voltage (200-210) out of a BN44-175A Samsung Power supply


If no voltage out either a short on the line pulling it down or its at the source--usually one or the other. ... Toshiba Satellite Flat Panel Televisions

I have A Samsung 52 inch LCD TV model #LN52A580P6FXZA. The relay clicks at A random rate, there is A red light that flashes steady. It will not power up. All my standby voltages coming from the power supply are present as well as the run voltages. Power supply on voltage is present, inverter on voltage is present, occasionally, it will give A loud high pitched squeal. It never comes on. Any help would be appreciated.


... Flat Panel Televisions

Samsung TV Model LA40A650A1M back light intermittently strobeing and sometimes cuts out completely, powering TV off via remote and back on temporarily resolves issue, but returns at various times, have removed power supply board to check capacitors - look OK none appear to be leaking. Power supply board details Hansol LCD, Rev 1.3, Manf date 11 July 08, Model SIP 408A BN44-001947A I note in some posts for similar Samsung P/S boards it has been suggested replacing specific capacitors - any su


You can't see if a cap is good or bad jus looking at them they have to be measured>They loose their capacitance because they dry overtime.I do sugest that you replace you power supply module or replace all caps.Possibily you may have a broken ... Samsung Flat Panel Televisions

I have a Sony Model# PFM-42B2, that go's into saftey shutdown mode and give's error code "blinking standby led" of 6, all fans start up and voltages for the power supply board, Vs, 82.5v @ cn23 pins 8,9,10 and cn33 pins 7,8,9. Va, 60v cn42 pin 1, cn52 pin 1. Vcc 5.1 @ cn6 pin6. Vpr2 3.3v in standby at pin1. I have also checked the power supply control signals to logic cn7, VCEGO-8, PFCGO - 10, VSAGO - 6, and they show 3.1v, I have the service manual and I have training in electronics, I needed t


Since you already have the service manual, did you check whats the self-test diagnosis for this set? I do not have one for this model so if you can upload it to a file sharing site, I can dowload it and break it down for you. ... Sony PFM-42B2 42 in. Plasma HDTV

I have Samsung UN46B8000XFXZA LED TV. After power surge it will not come on. Plugging it in causes the blue power up light to come on for one second. The relay on the power supply (BN44-00270A) begins to click. The screen does not come on. All appears dead except for the clicking of the relay on the PS board ever few seconds.rnIf I unplug the connector from the power supply to the Main Unit Board (BN94-02661E) and apply 110v, the screen backlight comes on and there is no relay clicking. (


Yes based on your testing it appears that the power supply is at fault solely and you can opt to attempt a repair or replace it altogether. Unfortunately you will not be certain that the main board does not also need to be replaced until you have rep ... Samsung Flat Panel Televisions

I have a Samsung lcd-led TV Mod UN32C4000PD Ver #CN02 that has 6 blinks when you turn it on. You can here the samsung sound when you push the power but no picture or sound. I put a high power light to the screen but no picture. Also I ck the power supply and i have all voltages. Thank You Pat


This is a classic "Hic-upping" switchmode power supply problem. The protection circuitry inside the SMPSU, has sensed a severe potential problem, and is attempting the shutting of the set, down to avoid a fire, explosion, or both. This s ... Flat Panel Televisions

Samsung pn58c550g1fxza unit has no picture got sound,ihave my vs,va,ve, and vsc voltages when un it is power up but then they drop,when check disconneting x-main and y-main 1 at a time i get voltages


... Samsung Touch of Color PN58C550G1FXZA 58-inch Class Television 1080p

Samsung power supply powers up bn44-00165b sound no picture


... Flat Panel Televisions

Hi I have a TH50PZ80U that is flashing two red lights when I plug it in. If i press the power button for 5 seconeds it will flash 10 times. When applying power the AC relays click, after pressing the power button the fans turn on and the optical audio port is red. It will stay 'on' for 3 seconds and then the relays will click on turn off. No red optical light. If I test the P25 connector pin 1 voltage it will go to 15 Volts for about a seconed and then 0. This is only achieved by plugg


I'm 100% confident that a D-board replacement will fix this issue. I've worked on 8 of these and a D-board replacement fixed the issue you are having now. I had all the same problems with them but it is all related to the D-board (from previous exper ... Flat Panel Televisions

Samsung HP-T5054 plasma, 40 months old. Apply power, power indicator blinks several times normally then goes very dim but steady on. No picture. Have removed back of TV and inspected. All fuses verified good. No bulging or leaking caps. Have BN44-00160A Rev 1.2 power supply. Have multimeter. What next?


... Samsung PS50P7H 50 in. HD-Ready Plasma TV

Samsung BN44-00338B power supply will not power on


... Akai LCT3201AD 32 in. LCD Television

I have a Samsung LE37R4 LCD TV. The two 150mF capacitors and the 3Amps fuse, on the BN41-00521B power supply board, really exploded a few minutes after powering the tv. I have replaced them but the new components too exploded after 1-2 minutes. Maybe other components are to be checked?


... Flat Panel Televisions

I have a Samsung LN46A530 46" LCD TV. Lost my backlight and wondering if the two wire connectors feeding the R and L inverters is where I would meter for power, and if not what are these for ? Or is it the ribbon cable on the top left (it's pin ids are 1. 12v_cold, 2.FB, 3.FB, 4.GND, 5.GND, 6.LD, 7.LD). Would this TV use 12 V to power the inverters ??. The inverter enable is on (5V), so I assume it is either the pwr supply or the master inverter.


... Flat Panel Televisions

I have a samsung LNT4071FX/AA.2 wks ago had the power supply replaced by samsung due to a clicking noise when i turned it on. Now the screen flickering for like 1-2 mins every time I turn it . would this be inverter issue or the lcd itself. Please help!!AAAP


... Flat Panel Televisions

I have hitachi t.v. model p50s601 when i turn it on the picture appeares about 1 second imeddietly turns off when it turns off no audio and no picture. already changed the capacitors on the power board c553-c552 = to 3300uf to 100 volts. checked xbus/xsus apperantly no problem. on the power board there is a voltage of vs=88.3v appeares in seconds then imediatly goes to 0. my question is what else can i check? or what could be the problem? thank you for your assistence.


The main rail voltage is not building up and so there is a possibility of a high drain on the output sections. The +B voltage seems to come up and then flatter off as there is a negative feedback to the processor to cut off ... Flat Panel Televisions

Samsung Plasma won't power on


This is not a capacitor problem. set is only 18 months old - has something to do with x y sustain boards not allowing smps to power on the high voltages. ... Samsung Flat Panel Televisions

Need schematic for Samsung PSPF651B01A BOARD yhay is in my Dell W4201C. Need to know what voltages to look for, and where. Will not start up (no Logo Screen when I turn it on). Other site suggest to change out power supply electrolytic capicators


... Dell W4201C 42 in. Plasma HDTV

How to fix power supply bn44-00338b - Samsung 32 in. LCD Monitor TV


... Samsung 32 in. LCD Monitor TV

Power supply on a samsung has no va and vs voltages pspf321501c


... Samsung Flat Panel Televisions

How to troubleshoot Samsung plasma tv power supply


If relays are clicking, the problem could also be the diode connected to the relay or its own power supply. Check whether the relay is getting power enough to remain activated. This chattering can also be caused due to relays becoming weak or by ... Samsung HP-T4254 42 in. Plasma Television

I have 6 gp328 and my multi charger power supply burned i guess due to the variying of frequency, can i use diffrent power supply with the same output voltage of the burned power supply?


Yes,,the same input,output and also wattage.. ... Flat Panel Televisions

Hi, I have a Sanyo 50" DP50740 and need a dual voltage power supply put in or at least a 220volt power supply. What power supply do recommend and where can i get it since Sanyo only sells to authorized repair shops. thanks.


... Sanyo DP50747 50 in. Plasma TV

My samsung tv model ct-21m16mj, no power but the flyback is ringing, the low power supply is good


... Samsung Standard (CRT) Televisions

I have anew Sony 40 inch EX 520 series Led warranty not valid in India since purchased in Bangkok. The power standby light goes of very often and the Tv goes dead. If I switch off the power supply for couple of minutes and switch it on again the stand by light comes back on and TV functions normally. The TV is also very sensitive to voltage fluctuations and on Inverter power supply. Please let me know what could be wrong and how to solve this problem. Thanks


... Flat Panel Televisions

My hitachi 29in ctv power supply 110vac had a problem on zener diode will blown if we switch on the tv. what spare parts to change so that the power supply zener diode will not blown again and the supply voltage remain in normal condition.


The secondary output voltage comes out from is more than it should be there. That is why, the protection zener diode blows off, as soon as you switch ON the set. First find and repair the power supply regulator, for correct output voltage. Refer i ... Hitachi Standard (CRT) Televisions

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1185 seconds