Having problems with your Standard (CRT) Televisions ?

After 5 yrs.of excellent performance, my Toshiba 27AF45 no longer receives a signal through the Comcast Motorola DVR when I use the TV/Video button on the Toshiba remote control (CT-847) to switch between Video1, Video2 and Video3. However, it plays DVD's on the ColorStream setting and shows up to 81 channels on the TV (non-cable antenna) setting. This problem started several days ago after some power outages in my home. At first, the three cable settings (Video1, 2, and 3) started going out int



Answers :

Hi,
Do you get sound in Video-1, 2 and 3 while tv does not show picture in these inputs?
Does tv show input display on its screen and it gets change when you select next input?
I do have service manual/ schematics of this tv that has all technical info but there is no reset procedure to fix this problem. It seems hardware problem and symptom shows IC601 (Chroma chip) got bad and causing problem.
Let me know above asked info to proceed.
As you mentioned you want to keep this tv for its good picture and sound quality then yes, it worth to get repaired.
Thanks.
CERTIFIED TV EXPERT HERE, follow this information I provided 3 long solutions to this issue/s
Solution 1
Before we start taking things apart, lets try your simple remove power plug routine and power system back up. Also, please try your unit on a few different channels to see if your problem continues on each channel. Your Main Board, Power Board, T-Control Board are suspected problems at this time. Press and hold the power button for about 15 seconds, the unit should power down by itself after you have powered it on. If it does not, then do not be concerned. Let me know if the problem continues. The first link below will bring you directly to the troubleshooting guide if you need to continue forward with the same error. Additional information http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com
2
Lets focus on the external portion of the TV set first (95 percent of all TV problems are related to things EXTERNAL To the tv itself) Check the physical CONNECTION of all cables by removing each wire bare or RCA and reinstalling it (Each power cable as well), once you have removed one cable, check it for fraying, and if it is already bare, splice a new fresh connection for it. 5. Check to make sure there are NO OTHER uneeded radios, system nearby. these systems, when powered on, will cause electromagnetic interference and prevent more than just severe tv interference SURGE PROTECTOR Surge protectors account for more than 75 percent of electric faults to stereo equipment. Lets start with your AC Wall outlet. It is standard in america that 220 Volts from out of these outlets. This implies that each device will be using 220 Volts (From within that grid zone). If anything including an alarm clock is plugged into any AC outlet socket in the vicinity of the stereo equipment/TV, it will cause electric outage, and prevent electronics from even turning on! Your TV needs dedicated electric power. If your TV is located in the living room then unplug everything else in the living room. Lets plug the TV set into a Dedicated socket. Check all light switches to ensure that power is on for that outlet. Check the TV cable for Fraying both on the ac wall end and where it plugs into the TV. Check all GFCI outlets to ensure that all red reset buttons are pushed in, check the circuit breakers for proper connection and they are turned on. Now, lets try the TV set without it connected to any cable services, vcr, dvd, stereo system, etc. Please respond if we have found a solution.
3
When troubleshooting these units, there are always several variables to consider. First check to see what last occurred with the unit such as did the children play video games, did the electricity go out due to bad weather. You may see that there are many possibilities but let's focus on what occurred last to the unit. Once we determine what happened last, we may isolate the actual cause of the problem. The actual cause may be associated with projection issues, older versions (Picture tube), interference from devices located nearby, and even a radio turned on and located really close to your unit. This is normally known as electromagnetic interference to electronics and is very common with the error you have provided today. Please continue to look for anything EXTERNAL to the unit before looking at the internal components. I have been working on these a long time so feel free to follow up with me.

Repair Help & Product Troubleshooting for Standard (CRT) Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

After 5 yrs.of excellent performance, my Toshiba 27AF45 no longer receives a signal through the Comcast Motorola DVR when I use the TV/Video button on the Toshiba remote control (CT-847) to switch between Video1, Video2 and Video3. However, it plays DVD's on the ColorStream setting and shows up to 81 channels on the TV (non-cable antenna) setting. This problem started several days ago after some power outages in my home. At first, the three cable settings (Video1, 2, and 3) started going out int


Hi,Do you get sound in Video-1, 2 and 3 while tv does not show picture in these inputs?Does tv show input display on its screen and it gets change when you select next input?I do have service manual/ schematics of this tv that has a ... Toshiba 27AF45 27" TV

Signal problems set plays great even up to a week at a time but then start to see lines in screen followed by blue screen with no signal then set turns off by its self..happens with cable and antenna connections..turn set off and resets for a while..is their a board to replace..


... Vizio M260VA 26 in. HD-Ready LCD TV

Toshiba 42H83 42 in. Rear Projection HDTV had the hyper module capacitor problem that Toshiba put notice out about. Changed those then plugged set in picture came in the three lamps noticably showed green,red, blue at the bottom of screen noticed grey static area because TV was not connected to cable or other device. Suddenly TV turns self off, now when plugged in to outlet power light blinks three times set turns off with speakers acknowlegement(sounded like speaker). I apparently have power d


If you bought a hypermodule rebuild kit from www.TvRepairKits.com go back to their site and ask for help. If you just bought parts off the web and winged the repair its hard to ... Flat Panel Televisions

The original tv setting have been changed ,now there is no picture prior to them changing the settings ,we had lost the local channels but had cable now there is no picture at all at first is was a cable problem,we had a good picture, until they start playing technician


Its very simple try to cleck the restore or go to the menu setting or make sure its not in video mode.god bless ... LG 42PJ350 42 in. TV

When my cable company came out to fix a problem with cable box they switched out the cable to HTMI. I have a Toshiba 42inch that previous ran on Colorstream 2 for the pix. I feel the picture quality, both HD and regular, is not as clear with the HDMI cable?


... Toshiba 42HP84 42 in. Plasma HDTV

Input Problems When turned on, the HDMI1 input shows up in the upper right corner, then the set gives a no input message, also tried hooking cable directly to the tv and the auto channel search did not work, and the set does not respond to the remote. The set worked fine yesterday, and when I turned it on this evening it started this. Any help would be appreciated.


... Flat Panel Televisions

I have an issue with my LG 32LE5300, when you start the TV there is no problem but at the moment if you chnage the channels it does not change the image, it is like you have only one channel and little more time later the image dissapear and it sounds like old TVs when does not have the TV Antenna. Also when I am playing with my PS3 for moments does not recognize the Video at the HDM1, already change the cable and tested the PS3 in another screen an no problem. It is like the Video card is dam


... LG 32LE5300 Widescreen 32 in. HDTV

I have just recieved froma friend a Toshiba MW20FN1 (-R) Television and there is no remote with it. I have purchased a universal remote. My problem is I can't get the tv to switch from TV to Cable so as to search or set up all of the channels. It will not go over 20 channels. What is the universal remote code for this TV and how do I get the tv to correctly go up and down to all of the cable channels. Thanks.


... Toshiba MW20FN1 20 in. TV/VCR/DVD Combo

Turned on my soniq 32" tv like i usually would and it just started flickering, not giving me a clear picture. Checked the antenna cable, wasn't the problem. Have turned it off and back on, still flic


The problem with the SONIQ L32V11 A/B/C with built in or without DVD players is the Power Save mode.This will be from the Main PCB . The power supply/Inverter Pcd is not faulty. Can be fixed by just a small mod.Here is what you have to do go to CN 4 ... Flat Panel Televisions

My Viewsonic 4785P is out of warranty. Problem is showing in different ways: image stays but sound goes then comes back, or not; everything shuts down and then comes back, or not; other times there is a very strident sound as if the set will explode. A tv tech suggested on the phone that the mother board could be either about to die or corrupted by my cable device and advised to shut down everything for 24 hours. Went very nicely then ... for 3 days and the same thing starts same way again What


A problem like this can be caused by RF interference. Shut it all down again and move the converter, any cordless or cell phones, wireless PC's, routers, etc. so nothing is within 3 feet of your set. A poor ground on your converter can also cause RF ... ViewSonic N4785p 47 in. LCD TV

Problem: can't setup my LG TV model #37LG500H-UA. HELP!!! I've receintly got an LG TV and I'm having no luck setting it up. Firstly I have only a universal remote (no 'the orignial), secondly there is no 'cable' connection here at my Dad's-only antenna (do I need a digital converter box?). I was hoping to locate the owners manual with that I can usually limp my way through but 'no can do' in the manual dept. atleast thus far.


... LG Flat Panel Televisions

It started with the convergence going haywire, not fixed by restoring factory default or advanced adjusting of convergence. I turned the set off and unplugged it. The next morning it would not come on - only the green light flashing. Coincidentally (???) the cable box also would not even power on - had to be replaced. I researched and found the problem with the green light (DM board kit available with 7 capacitors and 2 fuses plus instructions). But, am I going to have to replace the convergenc


Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from ... Mitsubishi WS-55511 55" Rear Projection Television

I took my Sony Wega KV32FS120 off my digital box and put it in a different room straight on the cable (without the box) I have picture, but when I start the TV I have sound when the picture kicks in the sound disappears. Does anybody know what the problem could be? I have tried all the sound settings


I have found that the input menu can cause a lot of problems. For example, if your cable box input setting was set to high def with a component (not a coposite cord) then that particular input is looking for two lines of audio into them--so a total o ... Sony FD Trinitron WEGA KV-32FS120 32" TV

How do i program a toshiba ct-9952 theater view tv to an antenna? an does it need to be on the tv or cable setting?


Download the user manual to your Toshiba set from net. It will help you in this matter. ... Toshiba Standard (CRT) Televisions

Toshiba 57H82 has horizontal blur when starting up on HD mode , but over time the picture is clear. However, in Non-HD mode , very blurry but, gets better over time but never clear. What is causing the problem


This sound familar. it sounds like the hypermodule problem. idealy the best way to repair this is the past was to replace the hypermodule. but they are hard to find. Next idea is to repair the board. the way to do this is too replace 11 micro capacit ... Toshiba 57H82 57" Rear Projection Television

I have a Westinghouse 16h120S lcd tv. From the day I bought it, the sound volume has been too low, even when I set both the tv and the cable at maximum volume. The cable company sent a technician to my home and was unable to solve the problem. I called Westinghouse customer support and they were unable to solve it. It appears that this is ot a problem with the settings; rather, it is a problem with some defect in the hardware.


Simple test: connect to the tv an dvd player, of any kind, and see if the problem is the same. If it is then the problem is internal - the audio amplifier of the tv is either too weak or the speakers don't match to it. After reading several cus ... Westinghouse PT-16H120S 16 in. LCD TV

Really? cool... so I have a Panasonic HDTV 720p... just moved, no cable, but I have a TV antenna. Amplified indoor antenna. GE brand model 24700. I powered and connected the coaxial cable between the tv and antenna. Now I don't know how to set up the TV to get any local channels.


You need to go into on screen TV tuner/channel scanning setup page and change the signal source from CABLE to ANTENNA so it will scan again to pick up off the air signals. Please read the TV user manual for more details.\012What is the model nu ... Flat Panel Televisions

Toshiba Model MW14f51 STARTING SETUP function does not begin when connected to cable and plugged in (in this order),


... Toshiba Combination Televisions

Toshiba cx36f67 tv - having problems with cable


Download the user manual to your set, and refer it about what you are missing. To download it, click here. ... Toshiba CX36F67 36" TV

Hi, i have a proscan tv that i recently bought from a someone and in the back theres two slots for antenna's. an antenna a, and an antenna b. when i bought it,the antenna a had been used, like the antenna was still in there but it was cut off like a few inches if that makes sense. someone told me that if i get a remote that specifially made for the tv then i can use that remote to change the antenna setting, so the cable comes through the antenna b instead of the a. and im 99 percent its the ant


... Proscan PS35130 TV

I got a Mitsubishi ws-55411 from a friend and I am trying to set up the cable. this is my first HD TV. The cable comes from a wall outlet (no cable box). I followed the manual and attached the cable into ant. A and turned the input connection on. I am only getting channels 2-13, I think these are the same stations I would get with just an antenna and no cable which makes me wonder if the cable is being detected at all. I have confirmed that the cable is working, because if it was not I would not


Go to the customer menu and switch the set from air-antenna to cable.The set is in the air band and not the cable band hence only channels 2-13.Let me know if you need help.SD TECH ... Mitsubishi WS-55411 55" Rear Projection Television

I have a Sharp LC-42SB45U. A few days ago the picture started to flicker a little just at the bottom of the screen. Now it's starting to flicker a little throughout the entire screen. Could this be a problem with the HDMI cable or the cable box?


... Sharp LC42SB45U 42 in. LCD TV

My thanks to Guest however as mentioned I have no problems using the SET-TOP BOX remote with my TV! I want to use my NEC remote as a stand alone; as I still have ANALOG reception? So disconnecting my SET-TOP and using my coax cable direct from wall socket to my TV I should be able to receive the ANALOG channels? and that's not happening; so when I use my NEC remote and go to menue the AUTO TUNE BOX DOES NOT DISPLAY! and that is the problem!


... NEC Flat Panel Televisions

I have smasung dlp 6756/xaa after replace SMPS main board, when i turn on the tv I got burning smell found middle of the tv section hehind screen wheel looks like electrical signal cable burned off, i already changed lamp, changed SMPS board and finally burned off cable. I am tired of this process, right after 1yrs late since i bought it starts problem. first symtom was light blinking, on and off, so i replace lamp, and changed SMPS board and more and more. some say digital board problem or so


... Samsung HLT6176S Television

Hi i got a vhs/ dvd recorder from a friend who upgraded,but dont have a manual,i have set it up to my portable tv upstairs,which has a set top box,but dont really know if i have the cables right. the problem is i can watch the videos but cannot record them to dvd,when watching them the dvd button does not record,but when you switch to dvd the record button works, im sure i have the cables in wrong. please can you help me audrey


Hello Audrey,\015\012\015\012If you can watch the videos on the TV, your cables are correct, but you don't generally record a video to DVD using the record button. Most VCR/DVD combinations have a DUBBING button on the front of the ... Flat Panel Televisions

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1404 seconds