Having problems with your Flat Panel Televisions ?

My plasma samsung ppm63mf7: no power, all caps OK, ceramic fuses OK, I replace a failed sustainer board. Now power just clicks and blinking power lightrnSo I unpluged T-con board and Main board to check for shorts but problem persist.power board# bn96 03736a* does any body have experiance with this model Tvs

Answers :

I had a similar problem with mine, i had to change couple of caps but it still would not power on. I ordered one online and it seemed to solve the problem. the power supply board for the TV are a bit expensive but this guys over at had one for under 200 dollars, http://myoemparts.com/power-supply-boards/53-bn96-03736a-pspf771f01a-power-supply.html

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

My plasma samsung ppm63mf7: no power, all caps OK, ceramic fuses OK, I replace a failed sustainer board. Now power just clicks and blinking power lightrnSo I unpluged T-con board and Main board to check for shorts but problem persist.power board# bn96 03736a* does any body have experiance with this model Tvs

I had a similar problem with mine, i had to change couple of caps but it still would not power on. I ordered one online and it seemed to solve the problem. the power supply board for the TV are a bit expensive but this guys over at had one for under ... Samsung PPM63M7F 63 in. Plasma TV

Viera TC-P50ST30 My TV is DOA. No power, sound, etc. No standby light. Confirmed house fuse, batteries, plus, etc. good. Tried unplugging for awhile. Makes a noise when I plug in to powerstrip or directly to wall. Someone said possible short. Pulled back cover. Checked ribbon between power supply and main board. Meter reads 5 when main not plugged into power. Drops to 2-3 when plugged to main. Is that where the short is? Isolated main by disconnecting all other connections to main. Should I ju

This may help... ... Panasonic Viera TH-50PZ85U Plasma TV

Hi. I have an LG 47LB9DF-UA LCD TV with a video problem. Originally, I had problem with horizontal lines, accompanied with a lag. After a short time the screen would then get multi-colored vertical lines. If I turned the tv off, then back on, the lines would be gone. If I left it on, the process would start over again. I opened the tv and found two connectors from the power supply board to the main board loose. After removing then reconnecting them several times, the problem cleared up. I l

... LG Flat Panel Televisions

Hello, I have a Panasonic Plasma Tv, Mod. #TC-P42X1, the tv. doesn't turn on, and blinks the led of power 10 times, we found the SC board in short and was remplaced it, problem persist, now we remplaced the signal main board and the problem still, what do you sugguest for this problem?

Have you already checked the power supply section sir?power failure are often cause by a faulty capacitors at the power supply section.have a close look at the capacitors if you notice a deformed/bulging capacitors replace it and also resolder the co ... Flat Panel Televisions

Problem with TH-C50FD18:Gives off 2 blinks I replaced the D-board and the A-board to no avail. The power trips the moment the 15Volts ON occurs to send 15volt power to SS, D-board, A-board and SC-board. I found no short on this 15Volts line that is switched by the MC701 Power MICOM Processor. It looks like a 15Volt error is detected, nonetheless.That's why it always reverts to standby mode. Could this be a 15volts power regulation problem? (I suspected the affected unit could be the standby pow

... Panasonic VIERA TH-C50FD18 50 in. Plasma HDTV

Panasonic tc-p58v10- have no display and sound,power ltg lightup have no blinking red light for trouble shooting,checked all fuses all ok.could this be a main board problem

... Panasonic TC-P58V10 Plasma TV

Samsung ln40a530 Hello, I repaired the power supply on that TV. I changed four capacitor 10v 1000UF and 25v 1000UF and a small chip on the pcb QM806 (4894B: SI4894BDY equivalent) Now I have a good read on all output. Thank you for the help found here! But now I found a ground on the main board. 5volt is on the ground(short). I unsoldered some chip without result, the 5v is still on the ground. Could someone tell me what the problem might be?

HelloCheck the retifier diode for 5VDC for short. If it is OK, replace the regualtor IC [5VDC], if used. ... Samsung LN40A530 40 in. LCD TV

I have hitachi t.v. model p50s601 when i turn it on the picture appeares about 1 second imeddietly turns off when it turns off no audio and no picture. already changed the capacitors on the power board c553-c552 = to 3300uf to 100 volts. checked xbus/xsus apperantly no problem. on the power board there is a voltage of vs=88.3v appeares in seconds then imediatly goes to 0. my question is what else can i check? or what could be the problem? thank you for your assistence.

The main rail voltage is not building up and so there is a possibility of a high drain on the output sections. The +B voltage seems to come up and then flatter off as there is a negative feedback to the processor to cut off ... Flat Panel Televisions

Whenever i plug my sony bravia KLV-32U300A, it click twice and doesn't turn on,power sign goes completely off. I have to unplug from the power source, wait 5 mins and try again, it rarely turns on, but does so if you try it after 4/5 hrs. Once the tv on it works fine. how can i rectify this problem? is it from the power board problem or the main system board problem? Pls help me thank you.

Hi,\012\012This is an indication of out-of-regulation in the power supply section. The very\012common caused of this fault is the leaky\012electrolytic capacitor ... Sony Bravia KLV-32U300A 32 in. HD-Ready LCD TV

M228WDP-BZ - Pure white screen. Power supply board checked. Voltages through connector to main circuit board OK. Changed main circuit board without any improvement. Need to know the voltges that should be found at the connectors from the power supply board to the screen?

... LG 42LC7D-UB Television

Hi, I bought a Vizio L32 HDTV10A that didn't power-up. There were charred components on the power board (an 8-pin IC with heatsink and 2 resistors). I replaced the power board, and the power LED then turned on (yellow) when power was applied. When the ON button is pressed, the power LED turns green for roughly 8 seconds and then the power LED turns yellow again. Nothing else happens. I checked many components (fuses, capacitor ESR, diodes, etc) on the main board and the master and slave inver

... Flat Panel Televisions

Hello, I have a XT-37 LCD TV, Manufacturer- Pixxel. The problem- doesn't power on- only red light is on- neither response to remote nor power on button. I checked the power supply -MT070A- replaced all capacitors - checked it with simulated load - works . I suspect the problem can be the control board - CV028E_V5. Please advise, Thanks,

... Flat Panel Televisions

Led24a45rq hi, i have this rca led24a45rq that won't power on redb led light constant on, i have 12v coming from power supply to the main signal board could it still be power supply problem or main signal board tell me what you think it could be. or could it also be the back light inverter

... RCA LED24A45RQ 24 Class LED HDTV - 1080p, 1920 x 1080, 16:9, 800:1 Dyn

I have a WS-65611 that I have replaced the caps on the DM board. Before I did that, the power LED flashed non stop, Now it does the normal 70 seconds but when I attempt to turn it on, it shuts right back off. After attempting a power up I checked the error code I got a short protect error. I then removed the DM again and verified the caps were not shorted to the shield and checked the pico fuse and found everything to be good. Any ideas of where I should start looking??

Did you run the error code operational check? In not unplug the set and plug it back in. Press and hold the DEVICE and MENU buttons for 5 seconds and release. The LED should flash a certain number of times a short pause and another series of blinks. ... Mitsubishi WS-65611 65" Rear Projection Television

I need detailed schematics with wire codes and values for diagnosing problems I am having with a Westinghouse SK-26h520s. The original problem was a dead machine, no indicator light so no power, replaced power supply now have indicator light but no sound or backlight, figured bad main board. Replaced board, made no difference. Any information, help or schematics with points and corresponding values to test with a volt ohm meter would be greatly appreciated

... Westinghouse SK-26H520S 26 in. LCD HDTV

My Vizio 55XVT1A power on, has sound, but no picture. I changed new power board, main board, T-cond board, but it still same problem. What's wrong with it? Is it anything with inverter board? Than

If this is an LCD tv the backlight inverter is bad, a good way to check it is to shine a flashlight close to the screen and see if you can see a faint picture.Let me know what you find ... Flat Panel Televisions

Samsung s5053, will not turn on. clicking noise inside, screen comes on and goes off. No picture. checked voltage on pin 10 get 5 volts connector cn804-1. research on internet seems to point at main power board, but some think its standby power board. I was going to replace the PSPF501A01A board. But don't want to spend $100.00 on wrong board. Any advice will be helpful. Thank-You Ken

Ken, did you ever find out what was wrong with your set and have it repaired?I have the same "clicking" problem when first turn on the TV. First, it took about 30 secs clicking (came from the relay) then came on ok. The wait time gradua ... Samsung HP-S5053 Television

I have a LT37HVS Olevia flat-screen that has a similar problem to one of the posts. I had the same blue standby type light on the front that stays lit, but turning it on just makes this light blink, and no display. I did as the posts here sugested, peeled it apart and manually inspected all of the capacitors. To my dismay I haven't seen one yet that looks bloated or leaky. I have inspected the main power supply board, both display boards and the main board. There were a few capacitors that

If turning it on makes the light blink then its a clear case of open circuit.. Honestly there are lots of components like diodes, fuses, transistors etc., and either of them if shorted create an open circuit. I do not think this is a capacitor proble ... Olevia LT37HVS 37 in. LCD HDTV

M220va wont turn on when plugged in and has a small white led light on the bottom right of the front panel that slowly flashes on and off. i've heard this light will come on when there is any problem with any of the boards, kind of like a safty shut off indicator. this makes it hard to diagnose since you cant look at any of the symptomes. sooo... i was wondering if there were any "common problems" with this model that might most likely need to be replaced (power board? main board?) fuse se

... Vizio M220VA 22 in. LCD HDTV

I have a Samsung LN40A530P1FXZA. It will not power up. I get 2blinks followed by short quick blink and then it repeats itself. I have replaced the power supply board and also the main board, and it still will not work. Does anyone have any idea as to what is going on with this tv? I wish I had an error code book for this tv, but I do not. The only thing I have not replaced is the TCon board. Need someone's help.

Try to download the manual on www.retrevo.com to see the error code for sure..Before you decided to replace t-con board please refer to the manual first,,but there is the possibility that t-con was faulty.Hope it helps..don't forget t ... Samsung LN40A530 40 in. LCD TV

I have a LG37LF65 LCD TV. Several month ago it broke down, at that time power supply was repaired. After a while after switching it on picture started to shake and then totally disintegrated. I have taken it back to service they said this is main board failure but since I cannot find proper board. Is It sure that is main board fault or can it be anyithing else? Can I check anything to be sure?

Check the power supply voltages to make sure you don't have another capacitor going out (the first one replaced is probably OK). Poor filtering on a supply voltage could cause the main board to misbehave. If the voltages are good, the shop tech is ve ... Flat Panel Televisions

I have a vizio vp422 that made a loud pop and now doesn't have any picture or sound. When you power it on the vizio display light turns from amber to white but that's it. U have to unplug it to turn it off. I have checked the fuses and they are good. The capacitors look good visually. There are a couple on the power supply board that have a black cover over the top, so I don't know about those. I changed the main board and made no difference. Someone please help!

Replace its power supply regulator board as card basis. ... Vizio Standard (CRT) Televisions

I have a insignia ns-lcd37 that has sound but no picture so i assumed a bad t-con board i replaced the t-con board with a new same problem left tv on for hours in a darkened room i saw no backlight i checked all my voltages at the power supply every terminal checked out good what could it be

Its 100% sure that the source of the problem is the backlight inverter board. The fact that there is no backlight confirms this. You will need to replace the backlight inverter board to resolve this problem. If you can get me the part number off the ... Flat Panel Televisions

Samsung LN46A550 LCD power on/off problem again. Red light blinks 11 times, then clicks and then repeats the cycle. Only way to turn off is to unplud the set. Have checked capacitors and they are fine - no bulges. Replaced the power supply board and still have the same problem. What next?

Apparently this is a known problem with flat panel TVs made a few years ago due to bad capacitors in the power supply. This same problem appeared in computer mother boards at about the same time so that the capacitors went open or shorted causing pr ... Samsung LN46A550 LCD TV

Samsung HP-P4271 42 in. HDTV Plasma power problem. When plugged in, won't turn on, just red standby light. Checked fuses (has continuity), capacitors (visual looks good), noticed blackened bulb near fuse in power board... could this be the problem?

Yes,this is the problems,might have bad plasma screen panel itself.Have a tv tech.to check it out.If the plasma screen panel it dead,tv not worth repairing.Plasma screen itself will cost the same as a new tv,if u able to buy it. ... Samsung HP-P4271 42 in. HD-Ready Plasma Television

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 3.5422 seconds