A few questions: was replacement just a bulb or bulb with housing and was it OEM lamp from Samsung?
If lamp light is still blinking the issue it has is there---other possible reason would be a ballast that is not bad but putting out low voltage to the lamp or the supply voltage to the ballast is low for some reason.
Actually the set should if the lamp light is still blinking shut off the lamp.
Also are you hearing any high pitched or fan like sound when the set is on?
Suggested Questions/Answers :
It is recommended you read all this kind of situations
Replaced the lamp in Samsung HLN437W and picture is brighter but not bright enough even after adjusting brightness. Also lamp LED still blinks
A few questions: was replacement just a bulb or bulb with housing and was it OEM lamp from Samsung?If lamp light is still blinking the issue it has is there---other possible reason would be a ballast that is not bad but putting out low voltag ...
Samsung HLN437W 43" Rear Projection HDTV
My PT-60lc14 Shut down a few seconds after the lamp turns on and has 1 "lamp" LED blink every 5 seconds. This means it is either an open thermal fuse (not open when I tested it), a cracked lamp (looks like a big blister on the upper side of the lamp base), an abnormal ballast, or an abnormal main CB.
The question: Can the bulb cause the shutdown even though it still lights? Is the shutdown from current sensing on the bulb? This is not explained in the service manual.
Panasonic PT-60LC14 60" Rear Projection HDTV
Hello. my samsung HL61650A 61'' DLP tv is about 2.5 years old, and tonight it just shut off. tried to turn back on, got 2 'buzzing' sounds from the back, but it wouldn't turn on. unplugged, undid back cover, put blue switch to 'down', still no luck. now, it won't really even try to power on, and standby & lamp LED lights blink. do you think it is solely the Lamp that needs replaced? help!?
Samsung HL61A650C Television
We have a JVC HD-ILA 61'' FLAT SCREEN TV Model # HD-61G787-the picture has been getting progressivly darker over the past week - we installed a new lamp about 3-4 weeks ago and then tonight we installed another new lamp we purchased from JVC. We have also adjusted the pic, color, brightness etc controls, however the picture is still thr same - any idea what is wrong
\015\012Below are links for service manual, you must obtain a copy, to have even a any chance of repair. Work through the troubleshooting flow chart in the manual, this will help you isolate your issue, going darker, is usually a loss of ...
JVC Flat Panel Televisions
I replaced my lamp on my 60inch hitachi 60v710. The lamp indicator light had never came on, but my picture was slowly starting to become dim. After replacing the bulb my lamp indicator light is now on, it blinks a couple of times and the t.v. Shuts off. We have checked to make sure the lamp is in properly. we have even taken the old lamp, t(that was working when it was removed) and put it back in and still the lamp indicator light blinks. On the rear of the tv right behind the lamp is a mother b
Hitachi Projection Televisions
Primo i repair a sharp crt tv model 20v-l70m. it work normal for 5 to 10 min. after this duration it turn dark. i can't almost see the picture. the two resistor are ok. i tried also adjust the screen of the flyback then i also adjusted the brightness in the service mode it just improve a little bit but still the brightness is sufficient.
Sharp 25R-S100 25" TV
TV powers on and the LAMP light blinks. There is no picture no sound. This problem arose randomly and out of the blue. Some sources as well as other answers here recommend to replace the lamp, but the lamp glows bright. As well, I removed the lamp from the housing and everything appears to be intact. The blink codes for this unit only indicate that the unit is powering on and will be ready in 15 seconds. Other sources I have read also suggest the digital main board is toast. Seems to be quite a
Samsung HLR5667W 56" Rear Projection HDTV
got this tv not working.
found no power when conected and decided to remove back cover.
found blown PCB fuse and replaced it,turn the tv on and the picture came on for 10 seconds and when out but tv was still on since the logic board led was on,also noticed led on PCB started blinking.
pull power cord off and then plug back in turn power button on and got picture for 10 second PCB relay clicked picture died and led on PCB started blinking again.
what do you think?bad PCB or ba
Hello\015\012The power regulator PCB has some fault it it. It does not outs proper regulated voltages needed to the other PCBs in your TV. Normally Plasma TV power regulator PCBs are very difficult to repair, and PCB as whole should be replac ...
Philips 50PFP5332D 50 in. Plasma Television
Phillip 50PF9630A/37. I have a red blinking 7 times after a green light. i've allready replaced the 2 bulging cap on the bottom of power supply board and also a cap on the Y board (board on the left) although i sodered it backwards with negative on the wrong side, i imediately resodered it and it sitll doesnt work. i've even isolated and unplug the y board and x board independently to see if it will still give me a blinking red lights and it still does. i've checked every capacitors and fuse on
Hello sir Jose!!!!try to unplug the y sustain only and power ON your TV..and see what happen next..Please reply to this tread for immediate help.. ...
Philips Flat Panel Televisions
I have a samsung dlp model hls5086wx/xxa that recently stopped working. Lamp light came on so I assumed the lamp needed replaced. Replaced the lamp and still won't turn on and lamp light blinking. It also make a whining noise when turned on but I don't get a picture. Is it the color wheel or ballast? Any suggestions?
Samsung Projection Televisions
Hl72a650 Hi I have a Samsung hl72a650. Replaced lamp a year ago. Tv suddenly one day started to shut itself off and back on again. I have tried everything else I have researched online. Took lamp out and back in several times. When the tv comes on the picture is very bright and clear then suddenly the picture begins to loose color and shuts off and back on several times untill all 3 lights start blinking. I also started the tv with mute 182 power and selected options clear lamp, reset user setti
Color wheel issues replace light engine ...
Samsung model hlr4667wx/xaa. Will not turn on. I can hear it try. It makes the loading up sound, lamp turns on, but screen is still black. At first everthing would power up ok including picture, but a few moments after shut off. But now...just the noise. It also originally went from three blinking lights to two. Its not the lamp. Had already tried that.
Have you had a issue where you heard a high pitched whine or fan like sound?Examine the color wheel- can be done with lamp removed--look in the opening the lamp faces---is wheel intact or missing any pieces?The set will turn lamp on ...
Samsung Standard (CRT) Televisions
Okay, so my Panasonic PT-43LC14 went black in mid show last night. The bulb is approximately 18 months old. The LED indicators upon Power On are; Power LED blinks green for approximately 70 seconds; Then the Power LED switches to Red Blink, and the LAMP indicator blinks once every 5 seconds. Service manual indicates this means lamp or ballast issue. I've inspected the lamp, and it doesn't appear to be burned out. I've disassembled the TV and check the ballast for visual issues and see none.
Check the bulb again and look at the root of where the main stem comes out inside and be sure you don't see any bubble like appearence around the stem at the bottom there. If you do see this then the bulb is bad. Otherwise try this: Hold volume do ...
Panasonic PT-43LC14 43" Rear Projection HDTV
Power led and lamp led blink simultaneously on my jvc hd65s998 rear projection tv
You might need to replace your lamp driver, or ballast as some call it. This is what strikes the lamp to make it light. ...
JVC Projection Televisions
G board Hi. I have a Sony TV KDS-60A3000. The red power led was flashing red 5 blinks. I tried all the basic fixes and nothing worked. I got to the G power board and can see black on the C6501 and R6501 and one other area by the "LAMP DC". I have pictures of the board I can send you also. Thanks :)
Sony KDS-60A3000 60" HDTV
RCA 46 TV went dim and even though i turned the brightness up, still is very dark. Also, certain images will flitter on the screen like a fast rolling wave. only certain colors though.
If a LCD either a problem related to the back lights if used or a problem on the digital control (main board) and in either case not a do it yourself fix. ...
RCA L46WD22 Television
How to adjust for best picture a Sharp Aquos Quattron 3D LED LCD 52 inch tv. I'm having problem maintaining perferred brightness. Also when initial turn on the screen goes to channel then shuts down and the 3D screen comes on, I then shut down and start up again anf the required channel will come on and stay ??
This sounds like a setting that can be adjusted. What I like about some of the Sharp televisions is the av mode setting (preset brightness/contrast adjustments). I am not looking at the manual for this model so I'm not sure if this is an option on th ...
Sharp AQUOS 52in. LE820 LED LCD HDTV
I was watching TV tonight and when I looked back at the television (KF-50WE620) there was a dull red hue to the whole screen. I tried playing a video tape and it was there also. Turn off all input sources, and there is still a reddish background glow to the whole television.
I didn't think that I could have adjusted anything to do with the colour since I wasn;t even touching the romte, but pressed reset anyhow, and it made no difference. Help please!
Its a failing optic block and needs to be replaced they are however very expensive to but and quite alot to install too im sorry to hear of your misfortunate mishap good luck ok ...
Sony Grand WEGA KF-50WE620 Television
I replaced the lame and im still getting the led light blinking six times. The lamp was blown for sure !
Can you help
Sony KDS-R60XBR2 Television
I can't adjust my green on the converge menu. The arrow blinks but the line does not move. I can go on anadjust the blue and the red but I still don't have the bedt of color and I think it's because the green is not set up correctly even doing an AUTO CONVERGE.
Hi,\015\012\015\012If the green color can't be align anymore in the convergence alignment through the menu, this is an indication of faulty convergence board inside. Your unit used STK-392-110 as convergence chip(IC) mounted in the heat sink. R ...
Panasonic PT-47X54 47" Rear Projection HDTV-Ready Television
I replaced lamp on mitisubishi WD-60735. The Lamp light is still blinking yellow, the timer light lit up green, but lamp still blinking yellow
Are you sure you installed the lamp properly and put the door back so the interlock switch is functioning. Sometimes installing the lamp will get slightly displaced and is not plugged up properly and will indicate a lamp blinking light. ...
Mitsubishi WD-60735 Projection Television
Samsung hlp6163w dlp tv not working, new lamp, new ballast, still three blinking lights
If color wheel does not run lamp will not fire----with lamp removed have you looked at the wheel----if not running it will cause almost instant shutdown of lamp and the set.If the DMD board is bad time for a new set as it is well over 500 . ...
Samsung HLP6163W 61" Rear Projection HDTV-Ready Television
Hi, i got samsung dlp tv m# HL-P5063W.i changed lamp,ballest,collerwheel,and lamp door cover sensor. but tv still doesnt come on.once you plug in the power cord green lamp sign blinks 35 times then cutts off and one time stand by red light blinks,then green lamp starts blinking again. lamp never gets come on. please help.
Seemed like it is a problem with the power supply circuit. Check the circuit where the power chord is connected internally to the TV. You should see capacitors. Check for swollen or leaking ones that may need replacing. Check also for burnt compo ...
Flat Panel Televisions
Toshiba 62hm15 . we lost power, then the tv had blinking red & green blinking, ordered new lamp, still no results, still blinking, help!!!!
Toshiba 62HM15 62" Television
Replaced the lamp in my Optoma Rd50 and the screen still reads that I need to replace lamp also T.v still having the same picture problem as before replacement lamp? what else could be wrong?
Optoma RD50 Television