You might want to with a flashlight and or small mirror want to look where the lamp faces at the color wheel---it must be intact and not missing any segments
typical color wheel:
If bad or not moving at correct speed set will turn lamp off quickly.
Suggested Questions/Answers :
It is recommended you read all this kind of situations
I own a Philips DLP television model 50pl9126d/37 I just replaced the lamp on it less than 6 months ago and the red lamp failure light came on. I have opened the back and can see the lamp starting up for about 5 sec but then it quits. I have read a number of issues but was wondering if anyone who has had this similar problem figured out the solution. I have pulled out the lamp ballast but as far as I can see there is no sign of damage. When the ballast was in I removed the lamp and could see the
You might want to with a flashlight and or small mirror want to look where the lamp faces at the color wheel---it must be intact and not missing any segmentstypical color wheel: ...
Philips 50PL9126D/37B 50" DLP TV
My Dlp lamp has gone bad . I have a samsung 57" tv, model number xlt5687sx/xaa. I've taken the board out and don't know how to take out or know location of lamp. Does this model have a Dlp lamp? I see an enclosure number around the lens, is lamp inside lens?
Hi,\015\012\015\012Please double check your model no. Is that the real model no or HLT5687?\015\012\015\012Jdvillanueva ...
Flat Panel Televisions
I have a mistubishi WD-Y57. I replace lamp 7 month ago, and now my tv doesn't work. I have sound but no picture. I took off the plastic grill from the back of the tv to see what it was doing when I tried to power it on. I see the fan turn on and see the light trying to cut on. It flickers light. It try two times before shutting down. If I see light flicking, does that mean the lamp isn't the problem? I tried to read the code light by holding those two buttons in front of the tv. But am not sure
WOULD YOU LIKE TO SELL IT ..LET MY NO LEE ...
Mitsubishi WD-Y57 57" Projection HDTV
My toshiba 52hm95 i still without a picture replaced the lamp and the ballast,the color wheel spins(cut the knob with the plastic tip attached from the lamp access door to get it to power up while firing up had my meter hooked up to the lamp plug from the ballast and found to would read 2.5 volt then drop out,what is the problem. thank you
Did you change the bulb or the bulb with housing. 2.5 volt is start up volts. this is to check if the bulb is there or not. check that you have the bulb connected good you can test the bulb with a meter. on rear occations the bulb may not work even ...
Toshiba 52HM95 52" HDTV Projection Television
Okay, so my Panasonic PT-43LC14 went black in mid show last night. The bulb is approximately 18 months old. The LED indicators upon Power On are; Power LED blinks green for approximately 70 seconds; Then the Power LED switches to Red Blink, and the LAMP indicator blinks once every 5 seconds. Service manual indicates this means lamp or ballast issue. I've inspected the lamp, and it doesn't appear to be burned out. I've disassembled the TV and check the ballast for visual issues and see none.
Check the bulb again and look at the root of where the main stem comes out inside and be sure you don't see any bubble like appearence around the stem at the bottom there. If you do see this then the bulb is bad. Otherwise try this: Hold volume do ...
Panasonic PT-43LC14 43" Rear Projection HDTV
I have a samsung model# hlr6156w and there is no picture, but when I turn it on I see an electric current flash at the back of the ballast board below the lamp housing. This happens 2 times then shuts itself off. Does this mean I have to replace ballast board and lamp?
Flat Panel Televisions
I have a Mitsubishi dlp WD62625 tv and I had a new bulb installed in Nov. 2010 by a tv repairman. After installation he re-set the tv but the yellow/red light wouldn't go off. So everytime I turn the tv on the yellow/red light stays on. Its Jan. now and just yesterday I got a message on the screen that my lamp should be replaced soon. I read something yesterday that its a possibility the ballast is bad. If so where is the ballast located and is it hard to replace?
Mitsubishi WD-62725 62" Rear Projection HDTV-Ready Television
Hi, I have a 60VS810 60inch LCD projection and the blue power light flashes but no picture comes on...i just got it for free so i dont know how it worked before..yesterday i did get a blury pic on the screen that kept moving so i couldnt read the menu bar but u can slightly see the menu options..only the blue power light flashes nothing else..what could this be..the lamp looks good and the bulb is fine..what else is there so i dont have to pay hundreds to fix it
Flashes of blue light are fault indications. From the number of flashes occurs at one time switch on, you can get an idea about the faulty section circuit board inside. If you wish to get details about these blinks, ...
Hitachi 60VS810 60" Rear Projection HDTV-Ready Television
I have replaced my lamp in my DLP model WD-62526 Mitsibishi but the screen is dark, so dark that I have to watch it with teh light off. But the funny thing is it isn't as dark as it was when it went though. I hav eremoved the back to search for the ballast but I couldn't find it. I think I would have to remove some more components of the Tv to see where it is. Could it be possible that one of the fuses could of went in the tv which is causing the tv to be dark. Also the HDMI doesn't work either.
Mitsubishi WD-62526 Projection TV
Wiring diagram for ballast number ebcf-127-120v-lpf
The following sites contain all the information on the EBCF127-120V-LPF ballast.PC board layout:http://slug.blog.aeminium.org/2012/0 ...
I have a sony kdf-42we655 tv and when i plug it in i hear it click on. unfortunitly although it clicks on u cant see anything but black like its not on. I am not sure weather it is the ballast or lamp?
Please help me
Unplug the TV's power cord. Press and hold the power button for 30 seconds, repeat. Plug it back in and try again.If this doesn't work, you should contact a repair shop or the place of purchase. Is the TV still under warranty or extended war ...
Sony KDF-42WE655 Television
How do I replace a lamp ballast in my Samsung model # HLS5086WX/XAA?
The ballast should come out fairly easy---at the end of the 2 red wires where it connects to the lamp should be a single screw and the lamp has to be already removed---with the screw at the wire end removed the socket lifts up and to one side and the ...
Samsung Flat Panel Televisions
Hi there, my sony grand wega kdf60wf655 had stopped working and was flashing 5 red lights. I tested the voltage from the power board to the lamp ballast board and got a 272v dc. Just replaced the lamp ballast board and now get blinking lamp indicator. Tried a new spare lamp that i had in reserve and still flashing red lamp indicator every 1 second. Any ideas? thanksp i
Sony Grand WEGA KDF-55XS955 55" Rear Projection HDTV
New lamp installed per mfg. instructions. status indicator flashes red and lamp failes to strike. Is there a security interface circuit that will disable the unit if the rear access panel is removed or may it be removed for cleaning and access. Would the ballast caps or the ballast itself be the target of the solution to rectify this issue?
The status light blinking red is indicating that a fan has stopped. which is not allowing the set to power up. ...
Mitsubishi WD-52327 52" Rear Projection HDTV-Ready Television
Ballast problem? I replaced the lamp after it ruptured, and it doesnt work indicating yellow flashing led light, and voice command saying lamp not working. I tried 3 different times same problem. I also put the back cover back all times. I was told it may be the ballast
The ballast is possible if it does not light the lamp even for a few moments----about the lamp= generic bulb or a OEM Toshiba lamp unit? ...
Toshiba 65HM167 65" Projection Television
After i replaced the color wheel on my samsung hlr6167w, the lamp does not come on. with the interlock switch closed, I am not getting power to the lamp and ballast?
should there be a 115V coming to the ballast?
Samsung HL-R6167W 61" HDTV
Picture lost color to greenish black and white and rapid blinking. Lamp indicator was orange for many weeks previous. rebooted TV and lamp would not come on. Replaced lamp, now it will not power up the lamp. Is this failure just about the lamp timer/counter needing to be reset or do I need a new ballast as well? I'd like to test the bulb independently if I knew what voltage/amperage/ ACor DC to apply.
LG RU-44SZ63D Television
I have a samsung dlp model hls5086wx/xxa that recently stopped working. Lamp light came on so I assumed the lamp needed replaced. Replaced the lamp and still won't turn on and lamp light blinking. It also make a whining noise when turned on but I don't get a picture. Is it the color wheel or ballast? Any suggestions?
Samsung Projection Televisions
My PT-60lc14 Shut down a few seconds after the lamp turns on and has 1 "lamp" LED blink every 5 seconds. This means it is either an open thermal fuse (not open when I tested it), a cracked lamp (looks like a big blister on the upper side of the lamp base), an abnormal ballast, or an abnormal main CB.
The question: Can the bulb cause the shutdown even though it still lights? Is the shutdown from current sensing on the bulb? This is not explained in the service manual.
Panasonic PT-60LC14 60" Rear Projection HDTV