Having problems with your Flat Panel Televisions ?

Hi, my Phillips was hooked up and working fine directly to the DISH receiver using the HDMI 1. I moved and had to put the DISH receiver in another room and ran a coax cable to where the TV is now using the ANT in spot. I select TV as the source and choose channel 60 and no signal. I hooked up another TV and it works OK. Any ideas?



Answers :

Hey, I'm Seth. I work as a sub contractor for dish network. I am picking up that your problems are on TV 2? If so, you will need to go into the menu on the TV itself and look for, "channel scan" or "auto memory". Run a scan. If there are no channels found go back to the "channel scan" screen. You will see an option saying, "air" or "cable". Switch it to the opposite of whatever it was previously on and run another switch. It should be found. I hope this wasn't too confusing, good luck.
Hey murphypat321,

Sounds like the TV may need to be on ch 73 cable rather than 60 air. Try switching the TV to 73, if it goes to 69 then put back on 60, if goes to 73 good. Once you have that set go to your TV1 and bring up the menu. Go to System Setup (6) -> Installation (1) -> Modulator Setup (5) and change the TV2 setup to either cable if on 73 or air if on 60 and the picture should come in if everything's hooked up.

Hope that helped! You can email me at [email protected] if the problem persists.

Tommy Faust
DISH Network

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

Hi, my Phillips was hooked up and working fine directly to the DISH receiver using the HDMI 1. I moved and had to put the DISH receiver in another room and ran a coax cable to where the TV is now using the ANT in spot. I select TV as the source and choose channel 60 and no signal. I hooked up another TV and it works OK. Any ideas?


Hey, I'm Seth. I work as a sub contractor for dish network. I am picking up that your problems are on TV 2? If so, you will need to go into the menu on the TV itself and look for, "channel scan" or "auto memory". Run a scan. If there are no channe ... Philips 42PFL5332D 42 in. LCD Television

Will come on but no picyure or sound can get source select to work some times and when switch to another source the component hooked to that source works.


... Proview PA-37JK1A 37 in. LCD Television

I have a Curtis 24 inch Full HD LCD TV 2425A never used Trying to set it up and their was no book in the box it says to run Channel Auto scan .it is hooked up to Dish satelite ant. .to run the auto scan.I cant get it to go on channel 60 to program the dish remote Thank you Mr McMillan sr.


Used the tv remote go into tv Menu goto SETUP go down Ch. enter pick CABLE and enter again.Tv now will go into auto scanning for CABLE channels.After the auto scan done for the CABLE channels are finish.After this u will able to go to channel 60 to u ... Curtis Standard (CRT) Televisions

I just bought a Samsun Series 4+ / 440 / 450 (on the users manual lol) but when i try to hook up my DTV or PS3 using an AV cable, nothing shows up. In the Sources, it shows "AV" but when i select it, it says no signal. The AV cable is plugged into the channel 1 slot and it is on channel 1 when i switch to AV. Please help.


Is that the av channel? if so, how do you know your getting a signal from the ps3? try hooking the ps3 up to something else to make sure you have a signal coming out of that cable (this is where you have to start) if you have another device like a DV ... Samsung LN-T4053H 40 in. LCD Television

NS-LCD52HD-09 Source list will come up on screen sometimes. Tv is on dish system and uses dish remote. I have gotten the insignia remote and tried to exit to no use. What is the cause and what is the


... Insignia Flat Panel Televisions

I have a VSX-920-K Pioneer receiver, a DV-220KV-K Pioneer DVD player, and a Sony CRT TV with no HDMI input but only a video component input. I connected the dvd player to the receiver using an HDMI cable (for audio) and a video component cable (for video) as shown in the receiver's manual. I connected the TV to the receiver using a video component cable. I have set the HDMI Control option of the receiver to "OFF" to enable the selection of the HDMI input in the Input Setup Menu of the receiver b


... Pioneer Flat Panel Televisions

I have a 62HM95. I was planning to hook up to my computer for online internet TV, but the manual states "Never connect this TV to a personal computer". I have DISH satellite service with a HD DuoDVR VIP722K. This only permits me to access DISH services online, but not Netflix, Hulu, or other internet sources. Is there a way I can hook up this TV to access the full range of resources available online?


They forbid the use of this tv as a pc monitor because the DLP chip (the one that generates the image) will fail faster when static images are displayed. \012\012\012But that doesn't mean that you cannot use it as one . Connect it to an old pc ... Toshiba 62HM95 62" DLP HDTV

We purchased a Vizio LED Razor model #VM230XVT on 1/4/11 and it worked fine till this past weeked. Now when we turn the power on, all we get is the Vizio screen on the TV and will not connect to the channels. I've tried everything to get past the "Vizio screen" including unplugging the power fow awhile and still no luck. I brought in another tv and hooked it up to the same source and everything worked fine on the other tv. I took our new tv to another source and the same thing occurs, just the l


... Vizio Flat Panel Televisions

Receiving channels We are in a campground using our insignia remote and can only receive a couple of channels. When we go to another channel and try to go back to the original channel it is gone?? When we were at home we received several channels. We are in New Orleans not in a remote area??


Tried to save those channel in the memory. ... Insignia Flat Panel Televisions

Hello, I have a TEAC TV and I use it mainly for gaming, I don't know what the model number is, is there somewhere to check on the back of it or something? I don't have hte box anymore. But anyways my issue is that it won't show all of the Input Sources It should do, it used to show like 10 or more and now it only shows 8. And when I select "VCR" it uses HDMI insted, and there is NO HDMI option when I go to chose my input. Thankyou.


... Flat Panel Televisions

I purchased a hiteker 37 inch lcd tv...used it for 2 weeks with dish but wasn't an hd box...(no problems) moved hooked the tv up to hd and it constantly says to autoscan...so we hooked it up the other way...says the same thing.. usually after 5 or 10mins of watching tv...and the remote has went through 4 sets of batteries in 4 weeks??? Any suggestions?


... Flat Panel Televisions

I have an RCA F27442 TV without G-link cables and need to select cable tv channel input. The setup routine will not allow selecting cable channel input unless I first set up G-link. Is there any other way to set TV to receive more than 13 channels so I can use on my cable system?


Yes, enter the menu. Look for signal source (ant/cable) select cable. Then run channel scan. This is an older TV and will require some time for the system to scan the cable channels and adjust. The process could take up to 20 min. Do not disrupt ... RCA F27442 27" TV

I have a receiver for 2 tv from dish . had a small tv hook up in bedroom and it worked fine. put new emerson flaT SCREEN IN AND HOOKED UP TO EXSISTING CABLE LINE AND ALL I GET IS NO SIGNAL


Make sure on correct input ... Emerson Flat Panel Televisions

Repair guys says my R04U media receiver can't be repaired due to power surge. Can another receiver be used to operate my PDP-4340HD plasma?


... Pioneer PureVision PDP-4340HD 43 in. Plasma HDTV

I have an ILO - 32HD Television but the cable cord that comes from the wall does not have a place on the TV to connect to. There is an indentation labeled ANT in the shape of a USB port which it isn't, just shaped like one. How can this TV be hooked up to my cable service? Is my only choice to use the colored yellow, red, and white cords? If so, that is too bad because that means I can't hook up any other devices such as a DVD to the TV (without constantly interchanging them).


Your TV comes with HDMI, DVI, Component In and S video in. Since it has no Tuner built in you will have to use a Set Top box with either component out or if you buy an HD Set Top box with HDMI out. The later will be in your favor so that you can use ... iLO 3200 32 in. LCD Television

Have Protron PLTV-3250 TV and I was told the power supply board was bad. All indications concluded this was the problem. Replaced the power supply board (FSP194-3F01 power supply) and turned the TV on. It has power, but I have no picture. I can hear the sound from each channel, but that is it. I can change the different sources using the remote control and when I come back to TV, the picture (white fuzz or blue screen) will flash for a moment, then it goes black. If I select a source that


... Spectroniq PLTV3250 32 in. LCD TV

I have an Accurian 3223. I can't finalize the discs (4). When I go to tools, then finalize, press enter, I receive "change disc". This has never happened before. This is of utmost importance. In the event that finalization can't be done, would I be able to unplug the unit and take it to another location to playback what was recorded. The event was recorded using the HDD mode. I recorded using a CD-R disc


I'm assuming that the disk was properly recorded, otherwise there is nothing you can do, that disk is a coaster and all in it that hasn't been kept on the HDD is lost. To confirm that try to burn another disk and see if it delivers the same result. I ... Flat Panel Televisions

I bought a TOSHIBA 32KV500B tv. At the Initial Installation mistakenly I selected "yes" for 'do you want to search analogue channels?' guestion. And then I lost all my automatically selected digital channels and I cannot go back to retune the channels. I have no SETUP in the main menu and then no INSTALLATION option. I have 6 main thing: picture, sound, feature, install, program table, Source: tv. I have tried to use the APS but this one retunes the analoge chanells only. Please help me how I c


I had this problem and searched the internet for hours looking for an answer and was given the initial same reply as this and it does not work. To solve this problem all you simply need to do is press source button on the controller followed by press ... Toshiba Flat Panel Televisions

Put up a digital HD antenna outside on a 20 " ft pole. Used it on an older TV with the assistance of a SDTV Digital to Analog converter box. Recieved upwards of 30 channels very clear. Decided to hook the same antenna minus the converter box assuming this 2 year old HD LCD Flat Screen is Digital ready and have no need to convert anything to analog. I hooked the antenna lead into the ANT 1 (air) IN connection. Activated the Auto Program and it indicates that it searched for all available cha


Hello\015\012Although your Samsung has HDTV comailant tuner inside, it must get sufficiant signas strength to memorize all the HDTV channels. Normally HDTV signals are weak compare to analogue transnsmission signals, and contain more details. ... Samsung LN-T4061F 40 in. LCD HDTV

After selection an input option the input menu stays up until you push "exit". Then it reverts to the tv input option canceling out any other menu selection. If you then try another route to get rid of the input menu I tried using the visual tuning,(brightness etc.) it quickly files through all options over and over. What can I do? This tv has been great up until now.


What has happened is there is a controller for menus and the selection of channel's av hdmi etcafter a hwile with some tvs they start to go on the blink it coud be worse i have had people with tvs that wont change channel keep jumping back and people ... Vizio VX37L Television

Pioneer PDP-R05G I have a Pioneer PDP-R05G receiver w/ PDP-435PG display it made a loud pop and now the display is black. When I turn the receiver on it it makes a clicking sound and then about 5 seconds later makes another click and the fan stops. The display LED light stays red throughout all of this even when I try using the remote. Any suggestions?


A clear symptom of panel failure is described here. If\012you wish to get more details, check this site. Pull up older posts there. Check the site with patience, as it has over\0122350 posts now. All are related to\012electronic equipment repair he ... Pioneer PDP-4360HD 43 in. Plasma Television

How to hook up a surround sound system to a Vizio 47"smart tv. What ports do you use at the tv. I have the RCA connectors coming from the Pioneer receiver


... Vizio 47" M470NV 1080p 120Hz Widescreen Razor Led LCD HDTV w/802.11n & Bluetooth - Wirelessly Network Your HDTV

I got a 32lg3000-za using IDTV, Select country Norway, no IDTV tuning feature avaiable, choose Denmark, tuning in channel's but got just text-info like tv guides, no picture/sound...


... Flat Panel Televisions

I have a WS 55313. Do I just hook the Dish cable coming from the box to ANT-A ?


... Mitsubishi WS-55513 55" Rear Projection HDTV

My LG RZ-32LZ50 has analog tuner built-in. But How can I watch freeview hd channels?? Can I use Digital indoor antenna, or I need to get HD receiver with outdoor dish antenna as well?


You will have to put a modulator/scan converter in line to convert from digital to analog. ... Flat Panel Televisions

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2688 seconds