Having problems with your Projection Televisions ?

Status light stays on and we checked air vents. Could this be a lamp problem as the TV shuts down in a few seconds after the message comes up to check air flow which we did. Thank you



Answers :

Check that the lamp fan is working

Repair Help & Product Troubleshooting for Projection Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

Status light stays on and we checked air vents. Could this be a lamp problem as the TV shuts down in a few seconds after the message comes up to check air flow which we did. Thank you


Check that the lamp fan is working ... Mitsubishi Projection Televisions

Replacing light fan on Mitsubishi WD-Y65 after getting error code 42. I had gotten the good old "TV will shut down in a few seconds. Please check if the air flow is blocked," message a few weeks back and the TV shut down. Called Mitsubishi and they sent out a replacement thermal sensor under the recall. A week later a tech showed up, replaced the part, and the TV would not fire back up. The tech left saying he needed to check some things back at the office and would get back with us. He could n


... Mitsubishi WD-Y65 65" HDTV

Blocked air flow error message on screen. I cleaned everything inside tv. fans, screens ducts, general inyerior. Put lamp module back in place. left extra fans assiting airflow into tv. TV came on for about 15 minutes. just long enough for me to feel smug. then same error. the next thig on the list is a faulty themistor. I have looked for it and have not found it. i need to find it to check connections and if needeed replace it.


Without a moodel number we can't give you much help. There is probably a thermistor that is a two lead device bolted or clamped to a heatsink. It will likely have thermal grease under it. They are often about 1/4 to 3/8 inch square with a metal ta ... Flat Panel Televisions

When I turn on my Mitsubishi WD-65731 it shuts off in a few seconds after showing a message that says check to see if air flow is blocked.


... Mitsubishi WD-65731 65" HDTV

I have a Vizio XVT553SV that powers up but nothing on the screen. The Vizio logo flashes org to white for 1.5 minutes then the V comes on the screen for 1.5 minutes. It will repeat this over and over. I tried the factory reset and it didn't work. I have the back off and no capacitors etc look bad. I could check voltages but the are a lot of wires coming from the power supply and I do not have a schematic. Any suggestions ? Thanks


That problem sir is usually cause of faulty inverter board...Try to replaced inverter board to fix your TV.. ... Vizio XVT553SV 55 in. LCD TV

I HAVE 43PP8421 PHILIPS HD TV MONITOR, IT WAS FINE BUT NOW IS NOT, I GIVE POWER I RECEIVES, CLICK SOUND COME, THEN A DIM SOUND COME 1 C/S RATE, NO PICTURE, NO OTHER SOUND, I AM WORRY, I CHECKED MAIN POWER FUSES, JUMPERS BUT THEY R OK, PLEASE HELP ME TO GET IT WORKING? THANKS


... Philips 43PP9202 43" Rear Projection Television

Ok so... I was on my computer one day and... i heard a loud noise im another room. So I went to go check it out an come to find out my sister, knocked my playstation3 down on the ground. Now every time I turn it on, the screen stays black... nothing comes up. It wont even turn off by it self, you nave to unplug it just to turn it off. It rarely works, if you unplug an plug it back in over an over again. If im lucky, i can get it to work then... can some one please help? Please!! Thank you.


It suffered some kind of damage inside--someone who knows how is going to have to take it apart to see if it can be fixed ... Projection Televisions

Air flow error message again and again....


A few of these sets did have a issue, the lamp cartridge had some fine metal mesh around a few places where the airflow from the cooling fan contacts it, that mesh if there gets blocked with dust and will give this error as it is really the set dete ... Mitsubishi WD-Y57 57" Projection HDTV

My panasonic tv model number PT-52LCX16 to stop displaying the message air filter needs to be cleaned call for service and stop auto shutting off, the filter has been cleaned and a technician has come


... Projection Televisions

Samsung s5053, will not turn on. clicking noise inside, screen comes on and goes off. No picture. checked voltage on pin 10 get 5 volts connector cn804-1. research on internet seems to point at main power board, but some think its standby power board. I was going to replace the PSPF501A01A board. But don't want to spend $100.00 on wrong board. Any advice will be helpful. Thank-You Ken


Ken, did you ever find out what was wrong with your set and have it repaired?I have the same "clicking" problem when first turn on the TV. First, it took about 30 secs clicking (came from the relay) then came on ok. The wait time gradua ... Samsung HP-S5053 Television

OI HAVE A ZENITH H27H49S TV REPAIR MAN SAYS IT'S A SAMSUNG. TV HAS A POWER PROBLEM THE TV COMES ON NO PICTURE THUMBING SOUND. THE REPAIR GUY SAYS I NEED A YOKE SWIE2-0134 UNABLE TO FIND ONE. THE PREVIOUS REPAIR GUY SAYS HE HAS THE SAME PROBLEM WITH ANOTHER SET AND HAS BEEN LOOKING 8 WEEKS FOR THE PART ANY HELP YOU CAN GIVE ME WOULD BE GREATLY APPRECIATED THE TV HAS A HOOK-UP FOR A COMPUTER AND HAS ON-AIR WHICH ELIMINATES THE GENERIC PRODUCT THANKS


The yoke coil is very critical component of tv. it matches with the picture tube & the circuit. one can not replace with another kind of yoke. these yoke coils are very rare to get. i m so sad to say if it is not available you have to replace the ... Zenith Standard (CRT) Televisions

Hitachi 55PMA550 I have a Hitachi 55PMA550 monitor linked to a skybox. The Hitachi goes on into standby mode on power up, I then use remote to start the Hitachi, the standby light goes green (start mode) & picture comes on in 3-4 seconds mormally. But now after 1 second (without picture) Hitachi goes back into standby mode of red light. I can hear sky tv sound (Hitachi linked thru sky to sound) and checked all cable connections, they are ok. Any advice would be most appreciated, thanks.


... Hitachi 55PMA550 55 in. HD-Ready Plasma Television

Mitsubishi TV Screen. Model # WS65517 When I turn it on, the TV shuts off in 5 minutes. The message is that the air flow is blocked.


You need a new switch ... Flat Panel Televisions

I have a Westinghouse television, model #SK-32H540S. When you turn it on both the picture and sound come on (like normal) after about 10 seconds the picture turns off. I had a local television repair company check it out. They told me it needed a new panel. They cannot find one. Do you have a panel or know where I might get one? I'd appreciate your help. Thank you, Mary Jo Penry


Try website like Ebay.com to buy refurbish 7 in. LCD screen. ... Westinghouse LTV-27w7 7 in. LCD HDTV

I have an Akai PDP5016H television recently it will not power on , I have to push power button several times before it comes on , no picture and no sound , Occasional lly it will stay on with the AKAI logo blue screen and then the screen will change to gray or scramble gray. On the upper right corner it it will say" AIR 8" and at the bottom right corner it will say " fill screen" I looked at the power supply for any bad caps but did not see any visibly. I even check the power supply board f


There's a good chance you have failing electrolytic capacitors either in the power section or the inverter section or both.Any caps in these sections that look bulged at the top, or bulged/leaking at the bottom need to be replaced, and in your ... Samsung Flat Panel Televisions

When tv is turned on message comes up that tv will shut off....check for dust etc. Room is cool. Tried system reset. removed and reset bulb in place. Any ideas? Barry


Cool room will not have much effect on the inside temperature of the TV. Check for the dust on the air filters of the projector & clean them. Inside the projection TV there is thermal sensor which senses the temperature. If it is more than the ma ... Mitsubishi WD-52631 52" Projection HDTV

HI, I AM TRYING TO CONECT MY LOEWE SOUND PROJECTOR TO THE LOEWE TV VIA RS232C AND KEEP GETTING THE ERROR MESSAGE COMMUNICATION BETWEEN THE TV AND SOUND PROJECTOR IS CURRENTLY DISTURBED, CHECK POWER LINE TO THE SOUND PROJECTOR AND THE COMMUNICATION BETWEEN THE RS232C. BOTH OF THESE APPEAR FINE. PLEASE HELP. THANKS


... Loewe Flat Panel Televisions

Our 47LG55 flat screen TV just started flashing rapidly on and off with a gray box with the message " this function is not available" . We can't get rid of it . Is it the problem of remote controllr or the problem with the TV sensor? Will the Compressed Air or WD-40 method help? If yes, what's the exact procedure? Thanks dozen in advance for any advice and help!


... Flat Panel Televisions

Air filter message keeps coming up on Panasonic 60 inch . Help please


If that then set is a DLP? If the set is full of dust on the fans and in the air channels it may need to be taken outside and a air compressor used to dust it out--will look in some cases like a dust storm so do not do it in the house. ... Projection Televisions

I have changed out the H.O.T. and the flyback on my R52WH74 model tv because it wouldnt come on and it would make a chirping noise I checked all the fuses and capacitors now with the new parts in the green power button light comes on for about 2 seconds and then goes off with a low pitch chirp it does this 3 times and then nothing i checked all fuses and capacitors again and found that 3 are not responding one is cp049, rp050 and cp050 could thiese be my problem or is it something else?


... RCA R52WH73 Projection Television

AFTER LOADING VCD DISC, MESSAGE COMES UP "LOADING " AND THEN "WRONG DISC. AND LOADING DVD DISC" NO DISC" MESSAGE COMES UP IMMEDIATELY.


Hi,\012If you have necessary tools and test instruments, know safety precaution in\012basic troubleshooting try the steps below to solve your problem.\012Assuming that the disc is good.\0121.Clean the lens. ... Flat Panel Televisions

I have a Sony KDF-50 WE 655 and I suspect the fan that allows the lamp to come on is not functioning right. I have to wait for the fan to come on before the TV actually comes on. If the fan does not come on all I see is 6 red blinks right after I try to turn it on. Is this a fan problem? or it maybe the thermal fuse as well? Thanks


... Sony Grand WEGA KDF-50WE655 50" Rear Projection HDTV

Channel not available error message comes up on Sharp LC-42SB45U


Just a guess have you tried the AV button? ... Sharp LC42SB45U 42 in. LCD TV

We have an LTV-20v2 about 6 yrs old. Came home one day from work and the TV wouldn't power up. There is no sound no and appears as if there is no power at all. I tried a lamp (closer than my meter) to check the outlet. And the outlet works just fine. After reading some of the other posts, I checked the fuse which seems to check out ok. Any ideas would be great. Thank you. Lyle & Chris


Hi,If tv show no power sign at all that means power supply board is not working, replace power supply board to solve your tv problem.Required power board is available with ShopJimmy.com for $20 and handy person can replace it easily. Clic ... Westinghouse LTV20V2 20 in. EDTV-Ready LCD Television

50 Tv not coming on there's a constant clicking sound coming from the rear of the TV. The blue light on the lower left front corner is lit but tv wont come on there's not other sound or picture. Thanks


WELL IT MAY SEEM LIKE THE END BUT ITS NOT. YOUR TV HAS BAD CAPACITORS ON THE POWER SUPPLY.. THESE CAPACITORS ARE PREVENTING THE RELAY TO STAY OPEN AND GIVE POWER TO THE REST OF YOUR TELEVISION.. THAT CLICKING SOUND YOU HEAR IS THE RELAY OPENING AN ... Philips 50PFP5332D 50 in. Plasma Television

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0769 seconds