You can but the connection type is not the problem. If you have Coax cable or antenna type signal you need to put that into a tuner capable of providing the RCA (baseband or composite) video out with RCA audio as well. However if one is going that route with a HD display then the SVHS tyoe connector or even HDMI or some component level cables should be used to get the full benefit of the HD signal.
If your HDTV has no Coax input then it is not a TV but a display
device more like what is used in computers.
Suggested Questions/Answers :
It is recommended you read all this kind of situations
Can you turn coax into rca cables since the maxent I have doesnt have a coax input
You can but the connection type is not the problem. If you have Coax cable or antenna type signal you need to put that into a tuner capable of providing the RCA (baseband or composite) video out with RCA audio as well. However if one is going that r ...
Maxent MX-42HPM20 42 in. Plasma HDTV
Possibly did something in settings, as tv wont pick up signal on any input. it stared with my hdmi input....one day my sons ps3 no longer would work on tv. I figured hdmi input went out after I tried changing every setting in the input mode. Cable and wii still worked fine. one night I went to turn his tv off and hit wrong button. from that night on tv wont pick up signal on any input. No cable at all. Actually have cable coax, not hdmi for cable
Haier HLH32ATBB 32 in. LCD HDTV
TH-50PX77U inputs Only the coax and audio visual cable inputs work.
the composite and hdmi inputs do not produce an image.
the menu, and av cables are all in perfect picture, but nothing shows up when connected via hdmi or composite cables.
Many times a computer's post screens will not show up a TV set, and once the computer itself has loaded the drivers and settings, the set may need to be shut off and turned back on for the HDNI or PC signal to be detected.It is also possible ...
Panasonic Viera TH-42PZ80U Plasma TV
I have a Samsung PN50B650S1FXZA and the HDMI inputs do not work.The component video and RF coax inputs work. Tried different HDMI cables and different devices Blu Ray player and Cable Box.
Samsung FPT5084 50 in. Plasma HDTV
The coax input on my tv is broken off how can I connect the cable to it other than the red white and yellow cords which don't have a good connection either I have my dvd player hooked up to hdmi is there a way to hook the cable up using the hdmi cord without a cable box just the line.
Hi, unfortunately the only ways to get the signal to the tv is with either coaxial, the red white and yellow rca cords, or hdmi and also the " RGB " inputs, also called "component video input ". some dvd players have component video outs-that could ...
Samsung Flat Panel Televisions
Coax cable/antenna connection doesn't seem to work. It says "no input signal" although the cable works when plugged into other tv's. Other connections such as HDMI seem to be working fine. Trying to set up basic cable without a box. Getting frustrated.
Westinghouse LTV-32w1 32 in. HD-Ready LCD Television
Audio output I can't get the tv to output sound through the external digital coax output. i have a digital coaxial cable and a receiver with an input for digital coax but i can only get the sound to play through the tv speakers
Emerson 32" Class LCD 720p 60Hz HDTV, LC320EM2
I have a Maxent Plasms TV. My problem is it shuts off after a few minutes only when its connected to an HDMI cable. If its fed with an anologue input it works just fine. I've changed cables but th
Maxent MX5020 50 in. Plasma Television
The coax cable input plug is broken off. Is the any other way to get the TV antenna signal into the tv without replacing the plug?
Emerson Flat Panel Televisions
Fukuda 32" lcd tv
just over a year but its havinv a hard time detecting cable channels.getting really tired rebooting and auto tuning since it doesnt work often
Flat Panel Televisions
I picked up two Zenith/Concierge TVs (model H2735DT3) from a hotel that was upgrading, but there is no coax cable input in the back. There is a hole where it looks like a video card would go. How do I find the parts to replace these?
Zenith Standard (CRT) Televisions
I have a Hitachi TV model # 51s715. I lost vision only threw the cable coax connector a while ago. Recently I just lost the same thing, vision only, threw all the A/V connectors at once. I get video fine from the S/Video and HDMI inputs. What can be the problem and should I expect the same problem to happen from the S/Video and HDMI soon?
Hitachi Projection Televisions
I have a VSX-920-K Pioneer receiver, a DV-220KV-K Pioneer DVD player, and a Sony CRT TV with no HDMI input but only a video component input. I connected the dvd player to the receiver using an HDMI cable (for audio) and a video component cable (for video) as shown in the receiver's manual. I connected the TV to the receiver using a video component cable. I have set the HDMI Control option of the receiver to "OFF" to enable the selection of the HDMI input in the Input Setup Menu of the receiver b
Pioneer Flat Panel Televisions
I have an RCA F27442 TV without G-link cables and need to select cable tv channel input. The setup routine will not allow selecting cable channel input unless I first set up G-link. Is there any other way to set TV to receive more than 13 channels so I can use on my cable system?
Yes, enter the menu. Look for signal source (ant/cable) select cable. Then run channel scan. This is an older TV and will require some time for the system to scan the cable channels and adjust. The process could take up to 20 min. Do not disrupt ...
RCA F27442 27" TV
Hdcp compliant vizio 55" - now recieves message stating set op hdmi port requires hdcp compatible tv input. switch to a compatible input or do not use set top hdmi port. If TV input supports HDCP then the hdmi cable may be at fault.
Purchased new HDMI cable tried on all 3 hdmi input ports. No success. How do i correct this problem?
Vizio Flat Panel Televisions
I own a Westinghouse LTV-32W1 and I am trying to hook Comcast basic cable up to it through the coaxial input. But, the only coaxial input is labeled ANTENNA.. I had the TV scan channels from cable AND antenna and it only found one channel. Analog at that. But, it doesn't do anything. How do I run basic cable to this TV? I thought, because it was HD-ready that I wouldn't need a box. :/
If you are trying to hook it up with cable make sure that the Tv is on cable mode. You will not need to scan for channels if you are using cable. If you scan for channels you are telling the Tv that you are going to use an ...
Westinghouse LTV-32w1 32 in. HD-Ready LCD Television
My regza tv has a facility where you can change the input from scart1, scart 2, pc, hdmi, etc, etc, so you could change the input you are viewing and watch for example something on the pc. however, very recently the tv will start changing inputs on its own, without me doing anything. i'll be watching tv and the menu box will appear up on tv and it will turn itself onto pc of scart 2 of its own accord. no other cables are connected to the tv, but the scart lead from the cable box. i hav
Dear user,may be its a rust problem in your tv side buttons that auto changing the input.or may be its system board faulty.kindly hit the buttons with hard thing bt carefully.if its not work then try to do factory reset other wise its sys ...
Toshiba REGZA 32AV615 32 in. LCD TV
None of my component inputs are working i have hdmi hooked in for cable, a computer hooked in to the computer jack, and they all work fine. i tried my xbox 360 in every available input with the component cables and get no picture or sound i have used multiple sets of cables
Did you switch the Xbox HD switch to the off position? ...
Sharp LC-C4654U 46 in. LCD TV
Have isolated problem to vhf/uhf connection point. white lines flash in pic. w/a popping sound & if they stay for very long there is a buzzing as in over white or over modulation. problem shows when cable signal is fed direct to tv or thru vcr to tv. other tvs do not exhibit same problem so it's not the cable. have tried other ac outlets & same problem. other inputs; dvd, vcr work fine. cable signal thru vcr tuner fed to ht processor is fine but that is fed via component inputs to tv. sony has b
Hi,Problem seems with main tuner in this tv as other AV inputs working fine so please replace main tuner (TU2) to solve this issue.There are two tuners mounted on A board TU1 and TU2, please replace TU2 and part number would be written on ...
Sony KP-53HS30 53" Rear Projection HDTV-Ready Television
Can i use a dvd player for then broken coax input on my samsung flatscreen tv
RCA F27636BC 27" TV
I got a Mitsubishi ws-55411 from a friend and I am trying to set up the cable. this is my first HD TV. The cable comes from a wall outlet (no cable box). I followed the manual and attached the cable into ant. A and turned the input connection on. I am only getting channels 2-13, I think these are the same stations I would get with just an antenna and no cable which makes me wonder if the cable is being detected at all. I have confirmed that the cable is working, because if it was not I would not
Go to the customer menu and switch the set from air-antenna to cable.The set is in the air band and not the cable band hence only channels 2-13.Let me know if you need help.SD TECH ...
Mitsubishi WS-55411 55" Rear Projection Television