Having problems with your Flat Panel Televisions ?

I HAVE AN LG 42 PJ 350 R TV ... I HAVE MY PC CONNECTED WITH IT. YESTERDAY I BOUGHT NEW GRAPHIC CARD WITH HDMI PORT. I CONNECTED THE PC AND TV WITH HDMI ... IT DISPLAY WAS FINE THAN SUDDENLY AFTER FEW MINUTES THE TV GOT OFF BY ITSELF. THERE WASN'T EVEN STANDBY POWER. I UNPLUGED THE MAIN POWER AND TURNED IT ON AGAIN .... THE TV WENT IN DEMO MODE WITH A PURPLE BACKGROUND IN THE PICTURE... I TURNED IT BACK TO HOME USER MODE BUT ITS GIVING BACKGROUND SOUND IN TV MODE BUT THE PICTURE IS PURPLE... I A



Answers :

I think from your mobile virus had entered in tv reset the tv

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

I HAVE AN LG 42 PJ 350 R TV ... I HAVE MY PC CONNECTED WITH IT. YESTERDAY I BOUGHT NEW GRAPHIC CARD WITH HDMI PORT. I CONNECTED THE PC AND TV WITH HDMI ... IT DISPLAY WAS FINE THAN SUDDENLY AFTER FEW MINUTES THE TV GOT OFF BY ITSELF. THERE WASN'T EVEN STANDBY POWER. I UNPLUGED THE MAIN POWER AND TURNED IT ON AGAIN .... THE TV WENT IN DEMO MODE WITH A PURPLE BACKGROUND IN THE PICTURE... I TURNED IT BACK TO HOME USER MODE BUT ITS GIVING BACKGROUND SOUND IN TV MODE BUT THE PICTURE IS PURPLE... I A


I think from your mobile virus had entered in tv reset the tv ... LG Flat Panel Televisions

Hitachi 55PMA550 I have a Hitachi 55PMA550 monitor linked to a skybox. The Hitachi goes on into standby mode on power up, I then use remote to start the Hitachi, the standby light goes green (start mode) & picture comes on in 3-4 seconds mormally. But now after 1 second (without picture) Hitachi goes back into standby mode of red light. I can hear sky tv sound (Hitachi linked thru sky to sound) and checked all cable connections, they are ok. Any advice would be most appreciated, thanks.


... Hitachi 55PMA550 55 in. HD-Ready Plasma Television

Toshiba 42H83 42 in. Rear Projection HDTV had the hyper module capacitor problem that Toshiba put notice out about. Changed those then plugged set in picture came in the three lamps noticably showed green,red, blue at the bottom of screen noticed grey static area because TV was not connected to cable or other device. Suddenly TV turns self off, now when plugged in to outlet power light blinks three times set turns off with speakers acknowlegement(sounded like speaker). I apparently have power d


If you bought a hypermodule rebuild kit from www.TvRepairKits.com go back to their site and ask for help. If you just bought parts off the web and winged the repair its hard to ... Flat Panel Televisions

Lg 42Lc5D LCD Tv has no HDMi input from al 3 ports. we have sound but no picture. Tv works in antenna and cable mode, just not HDMI. i have powered down and reinstalled the cable but still no picture. any ideas tv is 3 years sold. [email protected]


... LG 42LC2D 42 in. LCD HDTV

MY SONY TV LCD MODEL KF-50WE620 screen went blank. When I turn on the green light it blinks on 40-46 times every second, then turn to red color to Stand mode and blinks for 160 times, then move to power off (red light). This TV has been OK for awhile until TELUS OPTIK HDTV (box) device was connected, shortly after 2 days I heard a loud single sound like a sound of a smoke alarm, just once, "squeeek". Then the TV Screen went blank. The other device from TELUS is still on.


There is no reply from the jungle IC301 (data bus is busy, shorted to ground, or held high), IK video path is defective. \015\012\015\012 Might check fuse, R607, Q601, IC601, R612 and VDR601 (should show open).\015\012\015\012 ... Flat Panel Televisions

We have a Hitachi P50S601, Ser # V7L019070, plasma TV. Turned it on and the power indicator light goes from blue to a blinking red light (Stand By Mode). The TV is connected to DIRECTV and if you are fast enough with turning the system on, you will get a picture for about 2 - 3 seconds, then the screen goes black. The power indicator light will go from blue to blinking red. Thank you for the assist.


It have short in some board have to checked by some professional. ... Hitachi Flat Panel Televisions

Sound doesn't work in HDMI mode, just picture. I tried buying a new HDMI cord but that didn't work either. Then one night the TV just turned off and now it won't turn back on.


Likely not related but HDMI does not like being connected if either unit is plugged in or powered up.As to the TV let me know the brand and model number and what if any lights at all come on when you plug it in etc.SD TECH ... LG 62SX4D 62" Television

I have a Vizio VL320M. Have had long standing problem with TV picture & sound going off for 5 to 10 seconds. Have unplugged TV and held power switch for 30 seconds then plugged it back in. Does not do any good. Lately, I have had a problem with the HDMI input. The picture shrinks top and bottom. I have to go through HDMI inputs back to the original to fix it. Have checked connections. OK. Any suggestions?


... Vizio VL320M 32 in. HDTV LCD TV

Sanyo dp50747 TV turned itself on and will not turn on. The green power light located on the front panel lights up and the side panel off/on works but no sound or picture is shown. The front panel green light stays lit. The TV did this again about one month ago but I just turned it back on. Yesterday, it turned itself on and now does not turn on with the sound or picture shown. There is no sounds or odors from the TV. The power outlet works fine and the TV appears to be getting some power


Sounds like a mainboard problem ... Sanyo DP50747 50 in. Plasma TV

My Akai LCT2660 is not connected to any devices. It has worked perfect for about 4 yrs. I was watching it for a couple of hrs. Turned it off for about an hr. When I turned it back on it briefly flashed a picture then I only had sound. Now if I turn it on it will briefly flash blue light on the right side. I checked the capacitor on the power supply and can't visibly see any bulging


... Akai LCT2660 26 in. HD-Ready LCD Television

I am having issues with my RCA Scenium D52W135D (playstation 3 connection). Recently, I have been having a very specific problem with this combo. I have it connected using HDMI to a Pioneer receiver (model# VSX-821-K). From this, an HDMI to DVI cable to the TV for HD picture. In the past, no issues at all. Recently, I can play DVDs/bluray discs and get full picture and surround sound. I can play PS2 games and get picture and sound. When I try to play PS3 games, I get sound through the rec


Had the same problem. With mine the other day you probably moved your Playstation 3 too another tv and set your 1080i,720,480 to high deaf on settings in Playstation. You have to change them back to automatic that TV says HDTV but it only plays Plays ... RCA D52W135D 52 in. TV/DVD Combo

I have a 13 inch Craig LCD TV. I turned off my tv, at first it would not go off when I pushed the power button. I pushed the button again and I no longer had sound, but I still had a picture. I pulled the plug on the tv to turn it off. Now sometime later I have pushed the power button to turn on the TV. I have a picture, but no sound. Can you help me?


Your problem has been caused by the cables getting displaced when you were pulling out the power cord.\015\012The simple and easiest solution to your audio problem is to switch off the TV. Disconnect all the cables. Wait for sometime. Reconnect the c ... Flat Panel Televisions

I'm not getting a signal from my DVR through the HDMI cable after a power surge. I was watching T.V. when the picture went.The video works because I can get pic + sound through an antenna and from


Are you able to test the DVr with hdmi with another television? ... Vizio E470VL 47 in. HD-Ready LCD TV

Every morning first start the picture does not come only the sound is Turn of then on it's ok but lately the tv will not even turn on Press on button either remote or tv the power light flickers for a couple of seconds then turns off again several attempts so Then I turn off power from wall gpo wait two minutes then try restart It does the same again but takes longer to turn off again until after More attempts it finally turns on but with no picture so turn off again then turn on and it's ok


The standby power supply has dried up capacitors, need to replace them, the tops have probably vented ... LG 60PY3D 60 in. Plasma HDTV

Magnavox 32MD350B/F7 On/Off keeps cycling. When pluging in the ac power the green light flashs then goes to red stand-by and back to a steady green light and then the whole cycle is repeated again no picture or sound. Cannot turn unit off at this time. After many times unplugging the power in and out, I may get it to turn on with a good picture and sound.


... SNK Magnavox 32MD357B_37 32 in. LCD HDTV/DVD Combo

Just bought a new Panasonic TC-L42U22, connected it to a samsung time warner HD cable box via HDMI, but the cable remote is not working. There's picture and sound, but can't turn it on or off, change the channel or anything with the cable remote. Don't know what to do.


You have to program the remote to work with your specific model tv. If it still doesnt work after that call your cable provider and ask them for another remote. ... Panasonic TCL42U22 42 in. TV

Binary File Detecting... error on my TV. I have a Devant 32'. We were watching a DVD through HDMI connecxtion when we suddenly lost picture and it displayed No Signal on screen. I checked all connections are okay and I did the power reset and still not working. And now, everytime I turn my TV on it shows the error message Binary File Detecting.


... Flat Panel Televisions

TV turns on but no picture no sound. Turn power button on but only the green power button located on lower right flashes on. For the last couple of months prior the picture would "skip" and I would have to turn it off then back on to get full picture. Less than 4 yrs old. Please help. Thank you.


If u are a electronics repairer,remove the power smps sectoion and replace the 820 or 1000 or 1500 MFd capacitor.it will be bluged.thank u ... Insignia IS-LCDTV32 32 in. Television

I have 50 inches plasma Hitachi TV (ALiS 1080HD). As the TV was on, the screen stopped showing (no picture) and no sound could be listened as well, without any reason. The power light started flashing (on and off) so I turned the TV off from the power supply (as the remote control was not responding). Few seconds later when I turned the power supply back on for a moment I heard a sound (making me believe that the problem was fixed) but once again the power light started flashing with the same en


... Flat Panel Televisions

Sylvania 13tv/vcr, has this code on the tv screen (8c1-0.19) when turned on. The TV has a picture,but no sound. The power supply seems to be okay, because when it is turned on it will play for hours,but without sound. There is intermittent use when the power button is applied, if it does not work the TV must be unpluged and pluged from the outlet to turn it on and off. Do you what this code is, and why is affecting the TV?


The fact sound works for a moment when power button is held and that you have to unplug to turn off or on means not a circuit problem but that the set is likely in the tech mode or service adjust mode.I think the best way to resolve this is c ... Sylvania 6313CE 13 in. TV/VCR Combo

I have the 42PFL5332D/37model...turned on one evening and had no picture but had sound. I turned off the power to check plugs and turned back on and now have no picture or sound. I have checked all


This sounds like a very common issue.If set is hard to turn on (takes several tries)but will eventually turn on hereis what my guess would be.Every set has a standby powe ... Flat Panel Televisions

DP46849 Sanyo. I have checked all of fixya for solutions. I hane no sound or screen but have a green light when turned on. It will flash as if it is in protect mode. I have checked voltage and there seems to be 5v, 12v and 15v as indicated on power supply. I cannot find a 24v to read from but I did pull the master inverter to see if I had sound. Still the green light flashes and no sound. I suspect power supply only because when it is turned off I hear a high pitched whistle that slowly goes on


Hi,Power supply board seems defective and causing problem. Please replace power supply board to solve tv issue, required board is available in ... Flat Panel Televisions

We had this TV gave to us. It is a magnavox 1988 big screen star picture in picture. Our problem is we have no picture no sound so we questioned them and they said its in sleep mode. How do we get it off if that's even our problem. We can hear the TV come on and power light comes on then we hear a click sound and the lights power sap and stereo lights are all on.


Unless you are lucky this set is beyond repair due to its age as most parts no longer exist for it, I actually have worked on a lot of those when they were fairly new-----Most common issue was broken or bad solder connections all over the set and age ... Standard (CRT) Televisions

I have a Samsung lcd-led TV Mod UN32C4000PD Ver #CN02 that has 6 blinks when you turn it on. You can here the samsung sound when you push the power but no picture or sound. I put a high power light to the screen but no picture. Also I ck the power supply and i have all voltages. Thank You Pat


This is a classic "Hic-upping" switchmode power supply problem. The protection circuitry inside the SMPSU, has sensed a severe potential problem, and is attempting the shutting of the set, down to avoid a fire, explosion, or both. This s ... Flat Panel Televisions

I have a TV plasma Philips 50PF9631D/10 since 3 years and since few days we have the following problem when turning on the TV: TV wants to turn on (power led on right bottom corner) turn green, sound starts but before picture starts, TV turn off and the power led is flashing red for while. If we turn off TV on power switch and restart again and again same procedure, TV finally turn on. I post the problem to Philips, they contact me, I expalin my problem and they let a Philips license reparer to


... Philips 50PF9631D 50 in. HD-Ready Plasma Television

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2908 seconds