Having problems with your Flat Panel Televisions ?

No 3.4 volt output


\015 The power supply output voltages are present except for the 3.4 volt output\015

Answers :

The 3.4 should be for the microprocessor area and comes from the standby portion of the power supply-----that voltage should be on all the time so look carefully where it comes from---some sets use a op-amp IC to switch it on etc and others a relay---

Like a car with no power or voltage start at the battery working outwards.

With that voltage missing the set should have no operation at all.

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

No 3.4 volt output


The 3.4 should be for the microprocessor area and comes from the standby portion of the power supply-----that voltage should be on all the time so look carefully where it comes from---some sets use a op-amp IC to switch it on etc and others a relay-- ... LG 37LP1D 37 in. LCD Television

Samsung PS42D7HD plasma TV has no pic no sound. Vs, Vg, Ve, Vscan, Vset volts are all correct. Heat sinks on X & Y boards are warm to the touch. RF In source and A/V In source have no output sound or pic. Remote Control buttons are detected by the TV as the blue LED flashes to each button press.


Take your scope and see if you have any activity on the LVDS cable on the main digital board as you press the menu button or the menu on the remote. If you do not see anything then replace the main board. If you do then the plasma displa ... Samsung Flat Panel Televisions

Hello, I have an Orion STV2763a with a solid line of white across the screen with about 2" of static below it. Found the LA78041 Vertical deflection IC to be bad, replaced it and d418 and d419, two 33 volt zener diodes and C414 [email protected] capacitor. still same issue, checked my voltages into the IC and are as follows. Pin 1 should be 3.9 v, varies from 2.4 to 4.6. Pin 2 should be 26v, is 29 to 31v. pin 3 should be 2.2v, is 2v to 3.2 v, pin 4 is ground, and has 0 v. pin 5 is vertical output, should


... Orion STV2763 27" TV

Hitachi 37ld8500 tv television switches on and off every few seconds continuously and will stay like that till its switched of. 24 volts are present at psu output


... Flat Panel Televisions

Set came in with shorted hor output transistor. Standby B+ is 180volts. Other supply voltages close to normal. With 60watt bulb for load the B+ is 142.5volts.


\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012"Set came in with shorted hor output transistor. Standby B+ is 180volts. Other supply voltages close to normal. With 60watt bulb for load the B+ is 142.5volts." (sic) ... Flat Panel Televisions

Iam having problem with a konka tv model kp2905qyt. there is no EHT but 130 volt is present on collector of horizontal output transistor, pleasse help


This problem has been answered a few while ago. Check the horizotal oscillator frequency. ... Konka Standard (CRT) Televisions

My Cyberpower CPS 1200 EI LCD Inverter output voltage is176V and varies with load and there are some times charging problems.


... Flat Panel Televisions

RCA TV 32V434T. F 800 was blown. IC 801 pin 1 and 3 was short. I changed IC 801. Then the red lamp in front blinks about 28 sec. Then a click and TV turns off. Have to unplug the TV to start again. IC 860: pin 2 to 8 = 169.3 volts, pin1 to 2 = 8.7 volts (this voltages even after the TV turned off) pin2 to 4 = 2.69 volts (after TV turned off 0 volt). IC 801: pin 4 to minus C 806 = 16 v; after click goes to 4,1 v.Pin 1 to minus C 806 = 160 v; after click goes to 4,8 v. D 869 c = 2,39 v. D 868 c =


... RCA 32V420T 32" TV

110 volts, rated TV was plugged into 220 volts power supply. Now when it was plugged into an 110 volts supply its not getting on? What could be the causes? and please suggest solutions.


... Philips 22PFL4507/F7 - 22 LED 720p HDTV

Can you plug teac LCD led tv LEDV24U83FHD to a caravan 12volt output? Or does it need a 12v regulator?


... Flat Panel Televisions

Viizio VT420M has scrambled Display, Sound, Backlight and PS outputs are all there


I would suspect the main board as well ... Vizio VT420M LCD TV

I have a 37" JVC LCD TV Model # T370HW02 and the left half of the picture if filled with vertical colored lines for approximately 30 minutes after the set is turned on then the picture clears up and stays stable. Once the set is turned off and cools down the process starts all over again when the set is turned on. Is this a capacitor gon bad? There are two 1000 micro farad 250 volt capacitors, one reads voltage (10.4 volts) and the other does not (zero volts) when the meter is in AC mode,


... JVC LT-37X776 37 in. LCD HDTV

In my tv ther s no audio analog output ,there s only optical fibre output ,is it possible to get audio output by using fibre optic receiver ?


... LG 26LH2000 26 in. HDTV LED TV

Sony ICF-212 transformer burn , it's an easy fix if the voltage output is known .. anybody knows the output of this transformer .. there are 2 output voltage.


Try to download the service manual to sony ICF 212, from internet. It will have all the details. ... Standard (CRT) Televisions

Audio output. I have it hooked up to the avr output, didnt see another output for rca's.. hooking it to my stereo system. the only inputs it has are rca's(red/white)


... Mitsubishi LT-52133 52 in. LCD HDTV

NO AUDIO OPTICAL OUTPUT-- NO VOLUME TURNED COMPLETELY DOWN(TO AVOID THE CRACKLE) IS TO BYPASS THE TV WITH AUDIO, CONNECTING STRAIGHT TO MY VIZIO VSB200 AMP/SPEAKERS FROM MY CABLE BOX AND BLUERAY PLAYER BUT ONLY WITH RCA CABLES- THERE IS AN OPTICAL CABLE OUTPUT FROM THE CABLE BOX ALSO BUT WOULD BE NICE IF COULD ROUTE THE SIGNALS THRU THE TV. HOW DO I ACTIVATE THE OPTICAL AUDIO OUTPUT AND TURN OFF THE INTERNAL SPEAKERS.


... Hitachi 42HDS69 42 in. Plasma Television

I have an LG 26LZ5RV TV. I have connected it from the RF output of my Sky+ box (using a coaxial cable) to the "Ant In" socket at the back of the TV. The RF output on the Sky box is set to Channel 35 and the power is on. I know that the output is working, as I have tested it on an old portable TV with manual tuning. My problem is that I cannot get my LG TV to tune in to the signal, using either auto or manual tuning. I have used System "I" and tried setting the Channel to 35 then searching b


... LG Flat Panel Televisions

My start up transformer out put only 43 volt instead of 125 volt, what is the problem , I replaced already 2 capacitor 160 volts, they get power from trafo, could the trafo is bad or something problem with another component?


First try to test the source of your ac input if one line is missing the voltage reading will be low if your input voltage is good try to test the ac wire of your transformer and the output line of your transformer. ... Flat Panel Televisions

My tv (AOC LE22H037) automatically lowers the volume down to zero. it depends on what kind of sound is it outputting: during movie whispers or song's almost silent intros, volume gets lowered down. its annoying because i always keep missing the first 2 or 3 words of any line. it is like, if the tv "senses" silence or almost silent sounds, it shuts down sound output. But if the input sound is continous, like in the middle of the song or the shooting of a submachine gun, output volume remains cons


... Flat Panel Televisions

Audio output I can't get the tv to output sound through the external digital coax output. i have a digital coaxial cable and a receiver with an input for digital coax but i can only get the sound to play through the tv speakers


... Emerson 32" Class LCD 720p 60Hz HDTV, LC320EM2

Hello, We have a HCD-HDX275 in the shop for no picture via Component output. It works fine through the HDMI. How do you change to the Component output? We have looked through the owner's manual, service manual, and Sony's web site to no avail. We have also disconnected the HDMI, hoping it would default to the only output plugged in. Still no luck. Thank you in advance,


Hello,cross check your connections and make sure the component is correctly connected. That is red for red, green for green and blue for blue.After the connections has be done correctly, select "Source" on the TV to "component ... Flat Panel Televisions

Analog Audio Out signal has very high distortion. Signal wanes in and out, wanders from one channel to another, and develops high static. This happens when Audio Out is configured for Fixed Output. When configured for Variable Output, the signal is perfect. Output is being used with Sennheiser RS120 wireless headphone set.


The problem is more likely to be with the wireless headphone set rather than the TV. It makes no sense that the signal changes channels. The only difference betweent he fixed and variable output is whether or not the volume changes the output signa ... Flat Panel Televisions

Onida colour television model co29ox5350bl the b+ voltage should be 135 volts when i switch on the voltage 135 is for a few seconds and the voltage is droped to 95 volts can any body may help me


... Standard (CRT) Televisions

Is my (110 volts) 47 inch Samsung TV completely damaged, or can it be fixed? My son accidentally plugged our Samsung TV directly into our 240 volt outlet without using our transformer. A small blast sound, some smoke and burning smell followed only for a short while.


Hi.Although technically you can get the tv repaired, a high voltage shot like that usually does so much damage to the electronics inside that it is more cost effective to just get a new tv.The repair costs are almost surely going to ... Samsung Standard (CRT) Televisions

I have a Telefunken TTV-3426 87cm CRT Television which had a cracked Line Output Transformer and was Arcing to a Heatsink on the Circuit Board. Eventually the TV stopped working. I replaced the Line Output Transformer but the television is still not working. I am now looking for a schematic/circuit diagram for this TV or advice on what else could have been damaged. Thank you and Best Regards


... Flat Panel Televisions

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0587 seconds