Having problems with your Flat Panel Televisions ?

I Have a problem w/ my Sharp TV 20V-S200 they appear a video in only a seconds and it fade to blue screen the sounds is ok but the video is the only problem when i always turn on the power it always appear the video in only a seconds and it always turn into blue screen please tell me the parts that i need to change thanks in advance hope someone can tell me the problem



Answers :

Dear Sir:
This a problem with HSYN+VSYN, you must follow the signal, and then the RGC. see the diagram
God bless you

5_14_2012_8_50_15_am.jpg

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

I Have a problem w/ my Sharp TV 20V-S200 they appear a video in only a seconds and it fade to blue screen the sounds is ok but the video is the only problem when i always turn on the power it always appear the video in only a seconds and it always turn into blue screen please tell me the parts that i need to change thanks in advance hope someone can tell me the problem


Dear Sir:This a problem with HSYN+VSYN, you must follow the signal, and then the RGC. see the diagramGod bless you ... Flat Panel Televisions

Ihave a Toshiba DLP TV 62HM 116 ,When I turn the TV on the screen is blak and the blu light under the screen is ON , the yelow light will blink 15 times and turn off ,stay off for seconds and turn on again ,blink 15 times and turn off again .Can you tell me what the problem is ? Thank you.


If model is as indicated here start by removing and examining the lamp that set has----shattered inside? ... Projection Televisions

My kdl55nx810 screen is blinking. While watching TV, the screen will go black for about 2 seconds, then come back on. It appears to happen intermittenly, every 15, 30, or 60 seconds. TV was working fine, when I went into the menu and adjusted the motionflow. I ended up returning TV to the original setting. When I started watching TV (after returning to original setting), the problem started. The TV does not turn off, but the screen goes black temporarily. Any help would be appreciated, thank


This problems,it can't be repair.The tv Tuner signal board is problems and the the causes.The tv Tuner signal board have intermittent problems.That the board,where the tv incomming signal cable plug into it.Tv is still useable wright?Use it the tv as ... Sony Kdl-55hx701 54.6 in. HDTV LCD TV

Hello, I have a Toshiba 57H84R rear projection tv that has developed a problem. Occasionally the screen would turn bright blue for a couple of seconds and then go blank (dark screen, like it had shut off). The red power button would go from a steady red light to blinking continuously and would have to be unplugged, then plugged back in to get it to come on again. One time it did this, there was a bright blue circle in the center of the screen and now there is a permanent yellow spot in the cente


I am 100% sure that this is not an issue with the CRT board(the tiny board attached behind the CRT's in this case the blue CRT). The problem is usually caused due to failure of high value resistors 500K-ohm or higher. Do you have an ohom-meter and kn ... Toshiba 57H84 57" Rear Projection HDTV-Ready Television

My Sony KDL-40XBR7 has developed two problems. 1) Sometimes when changing channels the screen turns green. I can solve this by turning off the set then back on, but what's causing the problem? 2) In the past few days whenever I turn the TV on there are horizontal bands from top to bottom. They are faint and the picture can still be seen. Additionally the picture is ghosted; a second ghost image appears larger and below the original. This lasts for a few minutes then goes away. Of course, the TV


... Flat Panel Televisions

When I turn on the set, the right half of the screen is distorted. It flickers, different colors move from center to far right of screen, double images that appear as negitives and sometimes that half of the screen is very dark. Sometimes it will clear up for a second or two then go back to the problem. When the problem first started, it only lasted for approx 10-15 minutes then the picture was great. Now it takes 1-2 hours for it to clear up. Once it clears, I get a great picture. The lef


Hi,Symptom shows problem with lcd panel (screen) however, t-con board that is part of lcd panel could be defective and cause of these symptoms.T-Con board is located at top center of cld panel at rear and would be covered with metal shiel ... Samsung LN46A550 LCD TV

I have an acoustic solution 32 inch HD TV. model number is LCD32805HD. power supply: AC 220-240V ~ 50Hz max:180W. The problem I'm having is. When I plug it in. The blue stand by light comes on, all appears fine. But then I go to start the tv up, it sounds like its booting up, but then I start to hear a clicking sound, the screen flashes to what appears to be a snowy screen. Then goes back to stand by. This all happens in the space of aprx 10 seconds. I have done some research and it looks like t


... Flat Panel Televisions

I just purchased a brand new M420nv 42 HDTV LCD LED and turned it on for the first time & the screen was white with blue vertical lines (very similar to a UPC bar code) on the left side of the screen. I tried to turn the tv off using the rotation dial on the side as the instructions state (for 3 seconds) & that doesn't even work. What is the problem with the tv? Is it a defect?


For sure a defect. You are looking at a T-con board that is faulty. Return immediately and get a different one. If it's within 30 days just swap out and avoid having to wait for a warranty repair!\015\012\015\012\015\012Please rate ... Vizio m420nv 42 in. LCD HDTV

The unit is around 3 years old. When the power button is pressed, the red LED turns blue and stays on, but the screen is black. If the INPUT button is pressed, a blue box appears in the upper right corner of the screen for a second, then disappears. Does anyone know what could cause this? I am not afraid to tackle electronic projects and have the correct tools...I just have no TV/LCD experience. Any help is greatly appreciated


There's a good chance you have failing electrolytic capacitors either in the power section or the inverter section or both.Any caps in these sections that look bulged at the top, or bulged/leaking at the bottom need to be replaced.If you ... Proscan 42LA45H 42 in. LCD TV

I have a Magnavox 20MF251W/37 that when I plug it in it turns on to the standby mode (red power light). When I power it on with remote or by pressing power button it does turn on (blue power light). Shortly thereafter, I do see an image (snow at this point since I don't have it plugged to any video source). However, that image stays on the screen for only 1 second then disappears. The unit is staying on and is NOT going back into standby mode (power lights stays blue). I have replaced main


Hi tempcheck,\015\012\015\012Lot of brand have a common symptom when there's a malfunction in inverter board, it will automatically shuts down the unit. This is because there is a protection circuit designed connected from this board to the mai ... Philips Flat Panel Televisions

My LCDTV has a problem, Model number is 6626LCT, Now on to the problem, While doing yearly cleaning on my tv as normal, after i plugged it in it was normal for 40 seconds, It flickered and the screen went from Black to white on the input menu. while watching TV it's weird, All the other colors, Red,brown,green,blue, etc turn up fine, It's just the black that has the problem, Like i mentioned before Black is now white, or a fuzzy mix of red,yellow,white,green, or one of each on it's


Only suggestion is if set was plugged in when you did what you did--unplug it and any box or receiver plugged in and wait a while--plug back and let the equipment try to reboot. ... Sylvania Flat Panel Televisions

I have a Polaroid FLM 3772 that when it is turned on has a whinning/humming noise and after 5+ minutes it almost completely goes away. As if it quits once the TV is warmed up and just recently the screen will turn greenish with vertical lines sometimes. The line problem will go away if I unplug and replug in the Green video cable. Can anyone tell me what this is and is it something that can be repaired and if so what part(s) are needed and where can I get them. Thanks Bobby


The humming/whinning sound is from the power supply module and it will get worst (bad caps).\012The lines on the screen can be caused by poor DC from power supply, or failing T-CON board, main baord, or worst case the LCD panel.\012As you ... Polaroid FLM-3732 Television

FLX3211b when plugged in the red power light comes. Then when the TV is turned the red light turns blue and stays on. The Element logo appears for a couple seconds then the screen goes black. There is a red light that is on inside the chasiss. Is it the power supply or main board


The transformer for the backlight is usually what fails on the elements especially if the logo comes up briefly then the screen goes out. I would check the transformers. ... Element Electronics FLX-3211B 32 in. LCD HDTV

When I turn the power on the light is blue but within a few seconds it turns yellow. No video is present on the screen.


... ViewSonic NX1932w 19 in. LCD TV

I have a LG 37LC2D that from past 2-3 days started behaving crazy.. It seems to respond very slowly to the remote and blank screen after the green light blinks for at least 15 times... Sometimes when I keep it turned on.. after sometime the picture and sound appear and when it appears its not a problem at all... Also, sometimes, after a few seconds, it flickers and then goes back blank... This would sometime occur only after an hour of two of watching... I read your forum and see that people


Yes that creamy liquid is called electrolyte. Capacitors with leaky electrolyte take longer to reach a proper charge/dsicharge cycle. they also tend to over heat after a while which is why it will shut off. As for calling a tech he will probably char ... LG 37LC2D Television

I have hitachi t.v. model p50s601 when i turn it on the picture appeares about 1 second imeddietly turns off when it turns off no audio and no picture. already changed the capacitors on the power board c553-c552 = to 3300uf to 100 volts. checked xbus/xsus apperantly no problem. on the power board there is a voltage of vs=88.3v appeares in seconds then imediatly goes to 0. my question is what else can i check? or what could be the problem? thank you for your assistence.


The main rail voltage is not building up and so there is a possibility of a high drain on the output sections. The +B voltage seems to come up and then flatter off as there is a negative feedback to the processor to cut off ... Flat Panel Televisions

I have Sony's 43 inch Projection TV, its model no is KP-ES43 ME1. Problem with it is that it has lost Blue color from its pictures. Anything that is of Blue color turns into different shades of Green color. But one important thing which i would like to share is that when we turns on PIP (Pictue-in-Picture) mode, images on the right side of the TV screen looks absolutely fine but Pictures on the Left side of the screen still have the same problem. I want to know what is the real problem and its


... Sony Projection Televisions

I have a Sony KP-57WS510 and am having problems converging. The red works fine however the blue cross on the outside colums of the convergence pattern is off to the left. I am unable to move these blue crosses far enough to the center to correct the problem. The picture on tv screen has a blue shadded bar on the left side and a yellow shadded bar on the right. I can temporarily correct the problem by turning the television off and then turn it back on. However, the problem does eventually return


The tv convergence board it is dead.The tv convergence board require replacing 2 STK convergence ICS and some or all of it resistors too.U have all the tools and also can do soldering ICS works?Yes,tries websites like Tvrepairworld.com,Tvrepairkits.c ... Sony KP-57WS510 57" Rear Projection HDTV

My mitsubishi ws-65513 picture makes a pop noise then goes out with the sound but can still see video source info on corner of screen. then i have to turn tv off wait a couple of seconds then back on then tv will work for a shourt time before picture goes out again. i have looked at the four caps on the Dm board they dont look faulty or bulging but dont know if that is the problem


... Mitsubishi WS-65513 65" Rear Projection HDTV

Problem - I have NEO TV-2155 TX . When turned on a blue screen appears with red lock in upper left hand corner What to do with this code? Please help!


... Daewoo DTQ-13P2FC 13" TV

When I turn on my Sony Bravia 32" Class 3D KDL-32EX720, which I recently bought in walmart.com about 4 days ago when I received it. There is thin blue vertical line appearing in the center of the screen. It doesn't disappear though there is already a picture on it. What are we going to do with this? Do we need to contact sony customer service or walmart.com? Please tell us what to do. Thank you.


With a unit less than 30 days old, typically you can exchange it for a new one. Contact Walmart directly. If the store is close by, pack up the set and bring it back requesting a replacement. If needed, talk to a manager. There is no reason for y ... Flat Panel Televisions

I have an insignia ns ltdvd26 lcd tv. The problem i am having is the picture. When i turn the tv on... the picture is normal...then display freezes and slowly the picture will fade to black. If i leave the set on....occassionally the picture will come back on for a few seconds then fade to black again. The backlight still appears to be on when the screen fades out.


Good day!If your problem is pictures fade on and off...There are some points to consider like \015\012\015\012loose connectors on the power supply,main boards and inverter board ----reconnect a ... Insignia NSLTDVD26 LCD TV

Problem magnavox tv 25E50100aa. The screen has a large square black block that appears about 60 seconds after we turn the TV on. How do I resolve the issue???


Hi, In your tv the closed caption option is in on position. go to the menu and surf for the closed caption option (CC) and select it to OFF mode. the black squire will disappear. ok ... Memorex Standard (CRT) Televisions

My Mitsubishi WD-60C9 tv will not turn on any more. When I press the power button the status light will continually blink green, the blue welcome screen will come up and then after about 15 or so seconds it will shut off. Any idea what the problem is and how much it would cost to fix?


I am having this same problem and the tv is only about 1 1/2 years old. Please help!!! Thank you in advance. ... Mitsubishi WD-60C9 60" DLP HDTV

I have had a problem for a year similar to one described here, the screen goes black but the sound stays on. The video usually returns after a second but not always. Now the image has gone var dark with the image rendered in gray with very low brightness, It is a four year old 50" .


This is most likely cause is overheating, the plazmas use fans to keep them cool and they are subject to overheating issues, all plazma's not just Visio. Chech to see if you can hear or see any cooling fans running in the back of the set. \015\ ... V, Inc. Vizio P4 Plasma Television

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2439 seconds