Suggested Questions/Answers :
It is recommended you read all this kind of situations
I have not serviced one of these models before, 26XR9DA. The problem is no Picture Sound OK. The Bachlights come on for about 3 Seconds with Sanyo LOGO visible then go off with the High Voltage inverters powering down. 5 12 and 22 V lines are clean and steady I have changed a few electro caps but this TV seems too new for the common caps problems The B ON pin sits at 3.2 Vs and never changes during startup etc.
Im hoping there is a common fault for this symptom. Any help is most welcome
Hi mroulston,\015\012\015\012First check the brightness of the logo when it's first come on, you will notice that there was a slight changed in brightness if the one of the backlights was already busted. This is the very common fault I've encou ...
Flat Panel Televisions
LG 42LK520 LCD TV screen takes 20 minutes to come in clear. During this 20 minutes, top 2 inches of screen works fine, but the rest of the goes black or picture freezes off and on during this time. I was informed the most common problem is bad capacitors on power supply. So I purchased a whole new power supply, and changed it myself! But unfortunately it didn't fix the problem.... Need help please
Is it cable tv ...
LG Flat Panel Televisions
Read that this is a common problem...I have a VS-60111....when i
turn it on it clicks then goes right back off....I used to manage a
service department for a place called Conns. Sell appliance and electronics....well one of the techs i used to manage came , looked
inside then immediately said convergenc ic's. well i actually read upon it too the main board out was gonna change them but got scared off the saudering part...long story short, rought board to him he saudered two new ic's i just
You cannot be sure of the problem unless you try the error code operational check. Here are the instructions for doing itTurn off the tv from the remote and unplug it. Plug it back in . Press and hold the menu and Device/Input buttons on the fr ...
Mitsubishi VS-60111 60" Rear Projection Television
Have an Element LCD model number flx-3210 that loses raster after 1 minute. Audio is fine. No blink codes and all caps are fine. Checked ESR and replaced common failing caps already. ec17 and ec18 450v 10uf. Also changed d10 and FETs q17 and q16. Nothing changed.
When I lose raster, the LED D13 on the power board lights solid. I do NOT have any backlights on. Dark room tested and backlights go out completely when this happens. I also tested the two transformers on the inverter side of the pow
Hi Jeramy.These TVs are indeed re-branded Polaroid. You will not find the service manual under Element. You must find the equivalent Polaroid TV.The Polaroid Flx-3202 is the same as element flx 3202 and 3212 the FLM-3237 is ...
Flat Panel Televisions
Common tv problems:I have a Samsung Led TV of model UA40C5000 and I have been sufferening a problem since I bought it 2 years ago. The problem is that sometimes I can not change the channel or siganal
Samsung UA40C5000 40 LED TV
53" hitachi projection tv wavering colors n letering,had convergence board changed afew years back problem solved.had problem again new tech came put white oaste on board problem solved.now having same problem
Hitachi 53UWX10B 53" Rear Projection Television
HDMI board was changed. No sound. No possibility to change the source definition. Definition blocked only for: 720i; 720p; 1080i all 60 Hz. I have changed second time the HDMI board and the problem persists.
With old board (one HDMI imput burned) I have sound and I can change the source definition.
All replacement parts were new, delivered directly by Hitachi media Europe.
Hitachi 42PD9700 42 in. Plasma Television
I was watching T.V. and when I went to change the channel, the remote control wouldn't respond. I changed the batteries (generic) & the new ones didn't make the remote work either. I hit the power button on the T.V. and it did turn the T.V. on & off & changed the channels. I think the bulb or the eye on the remote is the problem. I can't remember ever seeing the bulb actually lit up. It is dark, so it seems it would be red. It's an old T>V> & remote, but has always worked. HELP PLEASE.
You won't be able to see the light from remote's LED (Light Emitting Diode) because it is IR (Infra Red) which is invisible to the human eye.\015\012\015\012Try re-entering the code for your tv to see if it works.\015\012\015\ ...
Flat Panel Televisions
My sony wega kdf-e55a20 stopped working recently so i decided to order a new lamp for the tv. This seems to be the most common problem with it, but when i received my new lamp it did not work. I decided to remove the new lamp from its case and put it into the old case. It still has not worked, and the light continues to blink red. What is wrong with my tv?
Hello espinosa pau and welcome to FixYa. I'm sorry you are having problems with your television but lets see if I can narrow down the problem for you. I'll need you to make sure your television is off then while paying attention to the area where the ...
Sony KDF-E55A20 55 in. LCD Television
Sony Bravia LCD KLV-32U300A Symptoms: ~ powering up problem, whenever try to turn on click twice and power goes completely off no standby indicator as well. i have to discharge the stored current in the caps to try the tv on but still the sounds click twice and goes.it rarely turns on after 4/5 hrs. In the SMPS board EADP-170AF A ~ board-G, CN202: "4VSB" pins 3, 7 & 8 have 4Vdc ~ other power outputs: CN201 6Vdc, 15Vdc, 30Vdc, "PWR_PANEL pin 7&8 ~ CN203- 24Vdc IN CN202 pin 3,7&8 4
Need to change color wheel on my Toshiba 62hm95 tv have not bought a new one yet. I got the old one out but the plug (where it plugs into board) came off This four pin plug is not marked or keyed th
I found some uploaded repair videos on youtube for this exact model tv.The guys user name is databits...here is the URL to his profile.http://www.youtube.com/user/databits?feature=watchNot sure if there is an exact fix for your pr ...
Standard (CRT) Televisions
My UNIVERSAL REMOTE (from shaw cable company) won't respond to my TV: LG 32LG30 .
Got another universal remote, same problem.
Can't use power button or volume on the UNIVERSAL remote but it will change channels through the digital box but nothing else will work.
Have sought help from shaw to program remote to no avail.
Is this a common problem with remotes?
The remote that came with the TV doesn't work either. According to the shaw service this TV remote should turn the TV on &
LG 32LG30 32 in. LCD HDTV
We have a Toshiba 42HM66 DLP. It is at least 3 years old and the lamp had never been changed. Lately the picture has gotten darker and once the unit is on for awhile the picture starts flickering and colors are not right. We assumed it was the lamp. Changed the lamp and still the same problem. Called Toshiba, they could not help but said picture flickering is not a symptom of needing a new lamp. They suggested we call a tech and they gave us a reference. The tech came out and agreed the
Check if the flickering happens when you have the menu up on the screen. If the menu does not flicker it may be the source of the signal or the connections to it or probable the board where the connections are terminating at. It may also be a prob ...
Flat Panel Televisions
I purchased an LCD Projection TV in November of 2007. Model no#KDF-50E3000, Serial No 8701626. I started having problems with it recently. It wont stay on. It turns itself off and then on again(the process takes about 30 seconds or more every time.)Does it every few minutes now. I have plugged it into a different socket and tried a brand new surge protector but nothing changed. This has been going on for 5 days now. I was hoping you might be able to help me with this problem. Have you heard
You have problem on power supply section.In most cases regulator ic and ic Mcz3001 is faulty. you need to replace these ic. ...
Sony Projection Televisions
I have a Sharp Aquos # LC-45GD4U. When I connect to the outlet red light starts blinking and pauses. I already changed the power supply and there is still no change. In the power supply i measured pludg p 7901 pin 7 , and it measured 6 volts no where else is there voltage. Can anyone offer a solution to my problem
If you have that 6 or 5 volts, that is your stand by, so power supply should be ok. I would think the main board,, check out these guys http://www.shopjimmy.com/ , you can call up and talk with a tech also there. I wouldnt think that the invertor wou ...
Sharp Aquos LC-45GD4U 45 in. LCD HDTV
21 inch LG tv switching on for 5 seconds and coming to standby. Again when I switch on the same thing happens. All Voltages are OK. The tv failed due to lightening during rains. I had replaced the vertical IC and H out transistor 1803DF. The anode cap was completely rusted and I had replaced it with a new EHT cap. What could be the problem for its switching off.
How about the regulator have you been checked if ok. ...
LG Standard (CRT) Televisions
I got lg pdp42v7 my problem is sparkle on screen I already put ysus and Zsus and also new logic replace all measuring and most all voltage are good somewhere I reed that I need to change some resistor on the logic change place but I can't find more information it will be great if someone can help me whit that
Flat Panel Televisions
New problem got no backlights changed power supply and ssb boards three times but still no backlights if anyone has an idea ow how to test them or fix it please help oh buy the way its magnavox 52mf437s/37 and they worked before ssb was changed first time
Do you have the 24V DC running into the Inverter? ...
Philips Magnavox 52MF437S/37 52 in. LCD TV
My Proview RX series LCD television is not responding to 'clicker'. (of course we first changed batteries to brand new ones.... not the problem) then something happened that's never occurred. It has a short memo on the screen that it is debugging itself. This has remained on the screen now for several hours with no progress. Do you have any advice. It IS connected to a DVD player that has not been any problem before. It is not connected to broadcast tv connection, cable or to internet.
Good day!Try to reset the power of the TV and DVD.Unplug it and after 30 minutes plug-in both TV and DVD to discharged the unit.Thank you. ...
Proview PA-37JK1A 37 in. LCD Television
Im working as a electronic technician in a garment factory.i have JUKI 1900 bar tack machine
There's a fault in main circuit board.
When I press the ready button, pressure foot goes up for a while n Itz comin to down position.acording to the my knwlage holding current of pressure foot solonoid is too low.
I changed the power transistor but the problem still same.I change the the circuit board and itz working porperly with new circuit board.pls help me to repair the old circuit board
If your problem is solve then ok otherwise call me 9915100566 kamali try to help you ...
Flat Panel Televisions
Pck5315r just changed convergance chips and plugged in to turn on nothing happened but tv started beeping. At first the colors were off and bought kits fixed problem but this is new problem.
Samsung PCK5315RX TV
My LCD TV Samsung LA40A550 have a problem with picture. The piture very bad, like negative photo. The color is normal. The samsung service agent say to me to change the LCD with a new LCD panel. its very expensive for me. its same with buy a new lcd tv.
Thank you for your advice.
Samsung LA40A550 40 in. HD-Ready LCD TV
Sony Bravia LCD KLV-32U300A
~ powering up problem, whenever try to turn on click twice and power goes completely off no standby indicator as well. i have to discharge the stored current in the caps to try the tv on but still the sounds click twice and goes.it rarely turns on after 4/5 hrs.
In the SMPS board EADP-170AF A
~ board-G, CN202: "4VSB" pins 3, 7 & 8 have 4Vdc
~ other power outputs: CN201 6Vdc, 15Vdc, 30Vdc, "PWR_PANEL pin 7&8
~ CN203- 24Vdc
I know its a 32 inch TVand its probably about 2 years old, give or take. If you got a warranty on it, I suggest calling whoever you got it from (BestBuy,Amazon, etc) and seeing what they can do for you to get it fixed for free. Otherwise call Sony ab ...
Sony Bravia KLV-32U300A 32 in. HD-Ready LCD TV
I think the sensor has gone bad in my TV? ordered a new remote but it did not fix the problem. i have to manually turn the tv on an off. You can change the TV chanels with the cable TV remote and adjust the sounds. how can the TV sensor not work with the TV's remote but the Cable remote will work on chanels and sound? what could be the problem?.
Sansui 32" TV
I have a brand new remote control, and new batteries! Still unable to get the remote control to operate tv. The tv is shows a small square box that contains the letters (LOCK)! My model of television is a Insignia Color TV; NS-20LCD! My satelite remote turns the tv on, but will not change the channels, or show picture! How can I fix this problem?
Press "0000" on remote ...
Insignia Flat Panel Televisions