Having problems with your Flat Panel Televisions ?

Elllo iv got a lg 50pc3d tv the tv blink 16 time wont open ive test my voltage and thats what it give to me original value 3.3v ---> 3.2V in real time original value 5v -----> 6.2V original value 6v ------> 7.4V original value 12v -----> 14.7 original value 19v ------> 24V would it be a powersupply? can u help me with this



Answers :

Not sure if it is a power supply issue for sure, but I've had a similar issue on an older model LG LCD TV. My symptoms were: in the middle of watching TV the screen blinked a magenta color for a moment and then the screen went blank, the TV would seem to turn off and on but could not get the screen to show anything, my power light would also blink 13-16 times and was delayed when turning off. after researching this forum I found a fix. Mine was a problem with a damaged capacitor on the power board it was a Samxon 2200UF 20V capacitor that had a slight bulge on the top. If you remove the back panel of your TV and locate the Power Board (the circuit board that the power cord plugs into) check and see if any of the capacitors on this board have any bulges at all they may appear very slight but will be on the top. If you you find any with bulges they are most likely defective. Remove the circuit board and de-solder the damaged capacitors with a soldering iron from the bottom of the board, and replace with a 2200UF capacitor (or whatever UF value is associated with the damaged capacitor) with a higher voltage rating of 25V or higher that way they will run cooler. Be sure to note how the original capacitors were put in (which side the negative connects to) to avoid damaging the new capacitors. I was able to find the capactitors at a local electronic store, but you could also find them online. The capacitors are $2-4 dollars each and a soldering Iron is approximately $10 at a local radio shack. This fixed my TV, cost me $12 with a soldering Iron and took approximately 1 hour to repair. If you do not see any damaged capacitors then it may be another issue, but it is a simple process to check, Again I did not perform this on the same model TV, but it was a similar symptom and an LG. Good luck!

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

Elllo iv got a lg 50pc3d tv the tv blink 16 time wont open ive test my voltage and thats what it give to me original value 3.3v ---> 3.2V in real time original value 5v -----> 6.2V original value 6v ------> 7.4V original value 12v -----> 14.7 original value 19v ------> 24V would it be a powersupply? can u help me with this


Not sure if it is a power supply issue for sure, but I've had a similar issue on an older model LG LCD TV. My symptoms were: in the middle of watching TV the screen blinked a magenta color for a moment and then the screen went blank, the TV would s ... Flat Panel Televisions

I'V LOST THE REAL VALUES FOR DEFLECTION SETTING IN SERVICE MENU FOR MY SAMSUNG CS-32500HEXA.PLZ HELP


Visit the site named 'Electro-help' for\012more details. Check this ... Samsung TX-T3093WH TV

I need how to change parameter in service mode of bpl bzr25 model when i m in service mode i can change the parameter value but change value is not memorised.pls help


... Standard (CRT) Televisions

I need detailed schematics with wire codes and values for diagnosing problems I am having with a Westinghouse SK-26h520s. The original problem was a dead machine, no indicator light so no power, replaced power supply now have indicator light but no sound or backlight, figured bad main board. Replaced board, made no difference. Any information, help or schematics with points and corresponding values to test with a volt ohm meter would be greatly appreciated


... Westinghouse SK-26H520S 26 in. LCD HDTV

I was replacing caps and thought I looked at all of them and thought they were all the same but one is a different value. I need to know if anyone has anyway of helping with this.


... LG 50PC1DR 50 in. Plasma HDTV

I have Sony kdl40bx420 LCD that will not power on. It's only 2 months old and was hit or dropped pretty hard and now nothing. If someone will help me with voltage points and values on G board I would be in debted. Thanks, Tim


... Flat Panel Televisions

Electro help green light indicator on for a second the supply board is on for output 12v 6v with backlight,then turn to red light blinking then the voltage supply is off with backlight.


It sounds that the back-light inverter has the fault. If there is any winding short [cannot detected by measuring with an Ohmmeter], this type of fault can occur. The only thing to do is replace the back-light inverter board. The LED blinks indica ... Sony Bravia Klv 46X300A 40X300A Multisystem Flat Tv

Hi can anybody help me with my jvc 52 inch tv the screen is pink , the picture is real bad


Is this unit a dlp digital light projection unit and a model number would be helpful so we can determine what you have ... JVC Projection Televisions

Toshiba 46 HDTV model number 46 H84. Went to bed turn the TV off got up the next morning I turn the TV on there was nothing on there it is slow blinking click like it was coming on and there's a red light blinking. Real slow blinking I have a video for you I hope it's good enough for you to see it because it's kind of dark. I hope that you can help me fix it without. Spending a lot of money because I have been laid off. Thank you and God bless.


... Projection Televisions

I bought my husband a ilive sound bar in Feb. 2012 of this year and the sound out it goes in and out and sounds real static !!! We have tried a new cord and still acts up. If I unplug it for a few and plug it back in it works fine for alittle bit and we loose it again!! Can you help me out please?


... Projection Televisions

Sony bravia 32" KLV 32V400A supply board resistor R 6193 is burnt What is its value will you please help me


... Flat Panel Televisions

My LCD tv works fine but has darted smelling real bad I'm getting headaches and getting dizzy please help


If you are not the only one smelling it I would suggest having a shop take a look (smell) as this might indicate some early warning of a problem. ... Sanyo Flat Panel Televisions

When switching on my plasma 42pma400a ,the screen lights up for a second and then screen goes off(completely off mode) ,then led goes on orange from green.The real problem is that i dont know where is thye problem located exactly?i mean is it in the power supply board or mother board?waiting for your help in advance...cheers mate


... Hitachi 42PMA400 42 in. Plasma Television

I have a Phillips DPTV335 with red ghost, I was giving 2 stk 392-110 to replace the original stk 392-120 well this work or do I have to change resistor values? Thanks for your help!


The 110 may work but you should always go back with the STK392-120 and also there are 12 6>8 ohm resistors that will need to be possibly replaced at least two will blow anytime an IC fails in that chassis so replacing the two ICs alone will most l ... Philips Projection Televisions

My main breaker blew on my house and voltage dropped way down, anyway i replaced my breaker box but during all of this something blew. the tv wont come on now i have been told i need a new power supply board and an new convergance board. any ideas as to where to look for these items. this tv is real special to me, it was my late fathers. i would really like to fix this for sentimental reasons. any and all help i appreciated thanks in advance


Even if there is a part that is not stocked usually ued.net can get it for you. Here is the list of parts they have listed for your televisionhttp://www.ued.net/ued/searchResults.do?searchStr=P61310&mfgCode=TCE&searchType=model&listParts= ... RCA P61310 TV

WHAT ARE THE foil side resistor values for RS1 & RS2 on a MLT566D MEGMEET POWER SUPPLY. ANY HELP WOULD BE SO APPRECIATED.BTW THIS JENSON TV HAD BEEN STRUCK BY LIGHTNING


... Flat Panel Televisions

I have a vizio l32hdtv10a, ineed help with the power module dps-199ap resistance 912, 913 burned out and i need the values of both.


Read ur manual ... Flat Panel Televisions

My sister has a Luxor V19LCDDVD875 TV from ASDA 8 days after warranty expired it developed high brightness. Reduce brightness and store works until next boot when (although the setting value is as stored) the high brightness returns. She has no user manual, it came without. Any help you can give much appreciated.


... Flat Panel Televisions

My vizio p50hdm made a popping sound from the rear. Afterwards, the picture disappeared and tv screen was black (as if the power was off). Then within a minute the picture reappeared but looked real dull with a weird contrast. I disconnected power cord, turned off/on the tv, and the picture remains dull. Tv has been this way for almost a month. In order to repair, I have to pay an estimate of $600, including parts and labor. Please HELP!


The z-sustain board is bad. One of the the heat sinks on the board is cool to the touch. These had LG circuit boards and the number on the sticker, on the board, was a good LG part number. The part numbers were 6871QZH044A.Do a search on ... V, Inc. Vizio P50HD Plasma Television

After a while my Sony Bravia kdl-26L5000 will go out to "fuzz mode" with fuzz sound and fuzz screen. To correct the problem, I turn off the TV and turn it back on. This is getting old real quick. Please help.


... Sony Bravia KDL-26L5000 26 in. LCD HDTV

RCA LCD X2620W TV no picture and possibly no sound. TV has no picture and cannot see if speakers are turned off as I cannot get see menu's. Set has 5v standby and 5v switched. I also have 12v switched. I also see 24v that is present with set on or off?. Any and all help is greatly appreciated.


Hi.The PSU looks OK. Double check that Volts are OK on all outputs.Check if there is DC out from main to inverter. If you have no back light: If there is no DC to inverter, then it is usually main board. If there is DC t ... Flat Panel Televisions

I have a 42 inch plasma hdtv model #42pa30rq and tha sound works fine but the screen is real grainy like almost infaredive tried everything from resetting it to picture settings i have only had it about two weeks please help


... RCA Flat Panel Televisions

My electrolux washing machine using EWM2100 PCB control board get a burn out R93 resistor. Pls help advise what is the value of this resistor.


... Projection Televisions

My electrolux washing machine using EWM2100 PCB control board get a burn out R93 resistor. Pls help advise what is the value of this resistor.


... Flat Panel Televisions

Radio Shack Multimeter, 22-168a, shunt resistor value????


Go to the Radio Shack site and you may with the model number find a schematic or you can email/contact them for the value of the resistor.I predict it is a precision value and type you will have to get from them if available.PS: you p ... Projection Televisions

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0840 seconds