Having problems with your Flat Panel Televisions ?

I hve dynex lcd 26-09 and there is 2 surfce mount resistors and 8 pin chip burnt up inside and the #s on the resistors were destroyed there is # on th board beside them but i dont know where to get the schematic to refernce these #s and get the correct resistor to replace them which i can do if i can determine the resistor from the # on the board. Where can i find the schematic?



Answers :

I think in the long run you will be better off to just replace the Board or Ship board to PTS for rebuilt
\0121-800-844-7871
\012Encompass Parts Distribution 1-800-638-3328 they might have Service Manual

Repair Help & Product Troubleshooting for Flat Panel Televisions
You need a second opinion or clarification ? ask it in the comment box OR you can Ask Your Own Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

I hve dynex lcd 26-09 and there is 2 surfce mount resistors and 8 pin chip burnt up inside and the #s on the resistors were destroyed there is # on th board beside them but i dont know where to get the schematic to refernce these #s and get the correct resistor to replace them which i can do if i can determine the resistor from the # on the board. Where can i find the schematic?


I think in the long run you will be better off to just replace the Board or Ship board to PTS for rebuilt \0121-800-844-7871\012Encompass Parts Distribution 1-800-638-3328 they might have Service Manual ... Dinex DX-LCD26-09 26 in. HD-Ready LCD TV

I have a HLR5656W Samsung. This question was asked before, but I never saw an answer. I have the same issue. "I have tried two different devices on the hdmi input and neither work. I am trying to find the part number for the circuit board that contains the hdmi input. Since I see no way to resolder or repair the connection I assume the board needs to be replaced? I was unable to get a part number over the phone. I was hoping to avoid taking the tv apart to get the board out and find the number


You need the service manual and you need to look at the exploded view to identify the board next\012go to the parts list if the part number isn't in the exploded view. ... Samsung HCM5525W 55" Rear Projection Television

LG 50PG25. No picture but good sound. Y-sus and Z-sus boards recieve good power. Z-sus board gets hot to touch on haet sinks and is noisy (buzzing). Y-sus does not get warm at all and is quiet. Are there any other tests I can do to determine cause? Thank you! D.Chase


... LG 50PG25 50 in. Plasma HDTV

Can't find specs for Samsung power board schematic and ZD601S component specs


... Samsung Flat Panel Televisions

The convergence board has a +20V & -20V input. The +20V is OK, but the -20V measures about 4.5V when the cable is disconnected from the convergence board. I could not find any blown fuses but R858 & R859 on the Main Power Supply Board "appear" to have been overheated. I can not tell for sure though without removing the board and without a schematic to know what their resistance values should be. Although R858 & R859 are in the immediate area, I'm not sure if they are even in the -20V circuit. Ca


Replace R858 and R859...They also go bad frequently when the STK chips fail. \012\012For everyone else...\012\012All projection TV sets have two very common problems. One is convergence ( 3D/Warped video or d ... Akai PT5598HD 55" Rear Projection HDTV-Ready Television

Hi, i bought a KV-HP212M83 4 years back. 1 year back, due to some over voltage in the line,the circuit board burnt away.since then we have been searching for its board and didnt get anywhere.its really sad that such a cool and good TV sitting idle at home ! It would be so kind of you to help us find the board of our TV and make it functional again.Patiently waiting for your reply. regards Anees Kurikkal +919946816899


Call Union Electronics at 1 800 648 6657. Be sure you have your TV model# and the board you are looking for. The other place is Andrews Electronics at 1 800 274 4666. These are professional services. I have used these services to replace boards, that ... Sony Standard (CRT) Televisions

Main Board? Had issues for years, where I had to unplug once in order to get the tv to turn on. Then one day, it would not turn on. The TV shows a quick lightening of the screen like it is going to turn on, but nothing appears. It also clicks once or twice. Took to a repair shop and they diagnosed with main board failure and refused to fix due to lack of parts. Do you think it is the main board and where would I find one? I am pretty handy, do you think I could DIYthis job?


The fault must be due to a main board fault. Generally, it will be impossible to get this board repaired. A replacement must be done. Most of the parts in this board are not available by local electronic spare part market. After power ON, there sh ... Proscan 47LB45H 47 in. LCD TV

Heve a phillips 60pp9202 projection. i had convergence issues being that i couldnt move my red. i went in and replaced both ics but i forgot to check the resistors. a week later i finally got in there and found 2 bad resistors. the thing is i didnt take the convergence board out, nor did i unplug anything when i tested the resistors. i put the cover back on until i get the parts. now, for some reason, when i power up the set it will come on like normal, then you hear a click and the screen will


Get a complete kit from www.TvRepairKits.com and start over.They will walk you though the repair. ... Projection Televisions

My electrolux washing machine using EWM2100 PCB control board get a burn out R93 resistor. Pls help advise what is the value of this resistor.


... Flat Panel Televisions

My electrolux washing machine using EWM2100 PCB control board get a burn out R93 resistor. Pls help advise what is the value of this resistor.


... Projection Televisions

I have a 53 inch hitachi proj tv...model 53UWX10BA....and am doing some of my own repairs...but one of the 1.8 Ohms resistors keeps burning out. The solders look good...I have tested everything and can not find anything wrong. Why does the same resistor keep burning out?! I must have gone through 6 or 8. I am at my end!!! Please help! The original problem is that the coloring is wrong. It is really RED. Am ultimately trying to get that fixed. Thanks!


1.8 ohm are protect on convergence ics --stk-392-110 or stk-392-150---Change both ics and make sure not shorted pins via solder connections.Let me know if you need help ... Hitachi Projection Televisions

Hello,have a thomson lodos tv model x28,the image started behaving strange and could listen sparks in the back.not very good with tvs but i repair hardware,so i opened the tv.found where the spark was comming from...its 2 resistances,they r next to a diod.in the board their references are R639 and R640 and they so burnt i cant see the collor code! been looking for the schematics but cant find them even with thomson...how can i find out what collor codes these resistances have and where to buy th


Thank you very much for the info provided.\015\012\015\012I hope this has fixed your tv! ... Flat Panel Televisions

I need to find out if there is suppose to be a resistor in the r206 slot for the vp322 power board


... Vizio VP322 32 in. Plasma TV

I have a Panasonic Viera 65" P65S2. After a month and a week the tv shut off, and when i tried to turn it on all i got was 7 blinking lights. I contacted Panasonic and a service tech was sent out to my home. The service tech said that i needed a SC board and he would order it immediately. It is now over a week and my brand new tv is still not working. I am now told that the part is on backorder for 2-3 weeks. I find this totally unacceptable and would like to get your view. Thank you.


I agree, this is not a good thing. A brand new TV should not fail 5 weeks into its life. Unfortunately, since the store won't take it back, you're stuck dealing with Panasonic's warranty group.Having to wait 2 - 3 weeks for a part is cr ... Panasonic VIERA TH-65PV500 65 in. Plasma Television

Where can i get schematics to find a capacitor. c160 or a transitor?


... Standard (CRT) Televisions

I need to find a t-con board for sharp pn-655. Would anyone know where I could get it? Thanks.


Send a emaiol to customerservice@tvrepairworld.com they should be able to assist you with that. ... Flat Panel Televisions

Finding schematic 4 the deflection board and capacitators CP 114,120, and150


No schematics are to my knowledge available for this fine thompson product---those are all right next to the flyback--a kit will include the one that removes the convergence option from the menu--one of the cp parts and a diode and filter cap are inv ... RCA D52W20 52" Rear Projection HDTV-Ready Television

Thanks Prasanna, but the audio output ic badly burnt and I cannot make out the inscription on it. I need to find out the Ic number in order to get a replacement. I don't have a schematic diagram.


What is the Brand name and model number to your TV? ... Standard (CRT) Televisions

Power supply Hi i have a PHILIPS FLAT HD ready 26PFL5322 I Think i need to replace the power supply board or smth like that but i cant find the prices anywhere or even where could i get 1?


... Philips 26PFL5322 26 in. LCD TV/HD Combo

Where can i find a service manual for the philips 37 pf9631d tv i need a schematic for troubleshooting thecomponents on the boards


What type of defect? most of these are board level repair. \015\012you can purchase the manual from encompass electronics if you need it. ... Philips 37PF9631D 37 in. LCD HDTV

My toshiba 50hpx95 has a steady blinking red light, it has no pauses or breaks to recite a code, just steady blinking. I had it in the shop and they said the power board needed replaced, so i replaced it and still get the same code. Is there a trap reset, or other mode of reset that i am not finding in the "service" manual, or was the problem misdiagnosed by my repairman. I cant even do a boot via service code thru the remote. is there a way to do a soft boot under low voltage so the chip can gi


This tv have a Tuner signal board it is also dead too,this problems happen sometimes,the power supply board dies,but sometimes the Tuner signal board take power surges from the power supply board itself than kiill the tv Tuner signal board too.Try we ... Toshiba 50HPX95 50 in. Plasma HDTV

I have a Samsung LCD TV - Model number LE37B679, which is great, but I'm having and issue with it. I can be watching ok for a while and then the picture goes & I'm left with a black screen. The sound remains. I find I have to turn the power off for 30 minutes or so then I get the picture back. Does anyone have any idea as to what might be wrong. I read something about a T-CON Video board issue, but I'm not technically expert enough to know if this is a red herring or not. Please help


... Flat Panel Televisions

Tv I need to find a replacement board where can I get one asap


Depends on brand, model number and a part number. ... Flat Panel Televisions

I replaced the STK chips and one pico fuse that was blown on the input power board (the fuses and resistors near the STK chips are fine). I turn the power on, no screen and I get sound for 1 second, then it turns itself off. The power LED blinks 4 times, long pause then repeats. What should I look at next.


A blink of 4 times is an error code that there is no vertical deflection. There may still be a problem with the + or - 15 volt supplies. This error is generate when the vertical deflection pulse is missing. there might be a problem with ic 8003 ... Sony KP-51WS500 51" Rear Projection Television

For welcomejee I have a Sharp TU-GD10U-T with at bad DC-DC converter board RDENCA089WJZZ. I'm an hardware EE, which means I may be able to repair it. I need the schematics or repair manual. Do you know how I can get them? Thanks, John


... Flat Panel Televisions

A detailed question is important to get you a relevant answers

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || fullblownbass.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1286 seconds